Panasonic KX-HNC600 Installation Guide - CA - Page 15

Setup, Part names and functions, LED indicator, Setup overview

Get Panasonic KX-HNC600 PDF manuals and user guides View all Panasonic KX-HNC600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Part names and functions G H I Setup Indicator Red, blinking slowly Red, blinking Amber, blinking slowly Status Live images are being viewed or recorded Camera is out of range of the hub, or device malfunction Camera is not registered to a hub *1 You can configure the camera so that its LED indicator does not light during normal operation. For more information, refer to the User's Guide (page 26). A B CD E F J Microphone Sensor range cap (Standard) Infrared sensor LED indicator Lens unit Speaker MN Used when registering the camera to the hub. Safety wire Camera mounting stand DC cable LED indicator You can use the LED indicator to confirm the camera's status. Indicator Off Green, lit Green, blinking slowly Red Status No power, or LED indicator is turned off*1 Normal operation*1 Registration mode Motion detected Setup overview 1 Initial setup Make sure you can access the system using your mobile device. For details, refer to the System Setup Guide included with your hub. 2 Registration Required only if the camera was purchased separately (i.e., not as part of a bundle). 3 Confirm the installation area Read the information in this document to confirm that the desired installation area is suitable to proper operation. 4 Installation Install the camera in the desired location and connect the camera to the power outlet. 5 Adjust the infrared sensor range Confirm the sensor range area and adjust it if necessary using the included sensor range adjustment caps. For assistance, visit www.panasonic.ca/english/support 15 HNC600C_(en_en)_0113_ver.201.pdf 15 2017/01/13 11:54:13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Part names and functions
J
C
D
F
E
B
A
I
H
G
Microphone
Sensor range cap (Standard)
Infrared sensor
LED indicator
Lens unit
Speaker
M
N
Used when registering the camera to the
hub.
Safety wire
Camera mounting stand
DC cable
LED indicator
You can use the LED indicator to confirm the
camera’s status.
Indicator
Status
Off
No power, or LED
indicator is turned
off
*1
Green, lit
Normal operation
*1
Green, blinking
slowly
Registration mode
Red
Motion detected
Indicator
Status
Red, blinking slowly
Live images are
being viewed or
recorded
Red, blinking
Camera is out of
range of the hub, or
device malfunction
Amber, blinking
slowly
Camera is not
registered to a hub
*1
You can configure the camera so that its
LED indicator does not light during
normal operation. For more information,
refer to the User’s Guide (page 26).
Setup overview
1
Initial setup
Make sure you can access the system
using your mobile device. For details,
refer to the System Setup Guide included
with your hub.
2
Registration
Required only if the camera was
purchased separately (i.e., not as part of
a bundle).
3
Confirm the installation area
Read the information in this document to
confirm that the desired installation area
is suitable to proper operation.
4
Installation
Install the camera in the desired location
and connect the camera to the power
outlet.
5
Adjust the infrared sensor range
Confirm the sensor range area and adjust
it if necessary using the included sensor
range adjustment caps.
For assistance, visit www.panasonic.ca/english/support
15
Setup
HNC600C_(en_en)_0113_ver.201.pdf
15
2017/01/13
11:54:13