Panasonic KX-HNS103 Operating Instructions CA - Page 8

Part names and, functions, LED indicator, Setup overview

Get Panasonic KX-HNS103 PDF manuals and user guides View all Panasonic KX-HNS103 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Setup Part names and functions A C B D E off by pressing M N again as soon as possible, otherwise battery life may be reduced. Indicator Green, lit Red, lit Red, blinking Green, blinking Off Status No water detected Water detected Sensor is out of range of the hub Registration mode (You pressed and held M N) No battery power Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 9). F G Main unit Main unit cover MN Used to confirm the status of the sensor or register the sensor to the hub. LED indicator Cable Probe unit Probes LED indicator You can press M N and check the LED indicator to confirm the sensor's status. After confirming the sensor's status, we recommend turning the LED indicator Setup overview 1 Initial setup Make sure you can access the system using your mobile device. For details, refer to the System Setup Guide included with your hub. 2 Insert the battery The sensor is battery powered. 3 Registration Required only if the sensor was purchased separately (i.e., not as part of a bundle). 4 Confirm the usage area Read the information in this document to confirm that the desired installation area is suitable to proper operation. 5 Installation Install the sensor in the desired location. 8 For assistance, visit www.panasonic.ca/english/support HNS103C_(en-en)_0224_ver.020.pdf 8 2015/02/24 15:14:55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Part names and
functions
C
D
A
B
E
F
G
Main unit
Main unit cover
M
N
Used to confirm the status of the
sensor or register the sensor to
the hub.
LED indicator
Cable
Probe unit
Probes
LED indicator
You can press
M
N
and check the
LED indicator to confirm the sensor’s
status.
After confirming the sensor’s status, we
recommend turning the LED indicator
off by pressing
M
N
again as soon
as possible, otherwise battery life may
be reduced.
Indicator
Status
Green, lit
No water detected
Red, lit
Water detected
Red,
blinking
Sensor is out of range
of the hub
Green,
blinking
Registration mode
(You pressed and held
M
N
)
Off
No battery power
Note:
R
The LED indicator does not indicate
sensor status if the sensor has not
been registered (page 9).
Setup overview
1
Initial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2
Insert the battery
The sensor is battery powered.
3
Registration
Required only if the sensor was
purchased separately (i.e., not as
part of a bundle).
4
Confirm the usage area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
5
Installation
Install the sensor in the desired
location.
8
For assistance, visit www.panasonic.ca/english/support
Setup
HNS103C_(en-en)_0224_ver.020.pdf
8
2015/02/24
15:14:55