Panasonic KX-HNS103 Operating Instructions CA - Page 9

Inserting the battery, Registering the, sensor

Get Panasonic KX-HNS103 PDF manuals and user guides View all Panasonic KX-HNS103 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Setup Inserting the battery R USE ONLY a CR2 Lithium battery. R Confirm the polarities ( , ). 1 Remove the main unit cover. R Lift from the indented area (A) and open the main unit cover (B). 2 1 Registering the sensor This procedure is not required for devices that were included as part of a bundle. Before you can use the sensor, it must be registered to the hub. If you purchased devices separately (i.e., not as part of a bundle), you must register each device to the hub. You can register each device by using the registration buttons or the [Home Network] app. 2 Insert the battery. 3 Attach the main unit cover. Using registration buttons 1 Hub: Press and hold M OTHER DEVICEN until the LED indicator blinks in green. 2 Sensor: Remove the main unit cover and press and hold M N until the LED indicator blinks in green (page 8). R When registration is complete, the hub sounds one long beep. Note: R To cancel without registering the sensor, press M N on the hub and on the sensor again. R If registration fails, the hub sounds several short beeps. Using the app When you register the sensor by using the [Home Network] app, you can assign a name to your devices and For assistance, visit www.panasonic.ca/english/support 9 HNS103C_(en-en)_0224_ver.020.pdf 9 2015/02/24 15:14:55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Inserting the battery
R
USE ONLY a CR2 Lithium battery.
R
Confirm the polarities (
,
).
1
Remove the main unit cover.
R
Lift from the indented area (
A
)
and open the main unit cover
(
B
).
1
2
2
Insert the battery.
3
Attach the main unit cover.
Registering the
sensor
This procedure is not required for
devices that were included as part of
a bundle.
Before you can use the sensor, it must
be registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the
[Home
Network]
app.
Using registration buttons
1
Hub:
Press and hold
M
OTHER
DEVICE
N
until the LED indicator
blinks in green.
2
Sensor:
Remove the main unit cover and
press and hold
M
N
until the
LED indicator blinks in green
(page 8).
R
When registration is complete,
the hub sounds one long beep.
Note:
R
To cancel without registering the
sensor, press
M
N
on the hub and
on the sensor again.
R
If registration fails, the hub sounds
several short beeps.
Using the app
When you register the sensor by using
the
[Home Network]
app, you can
assign a name to your devices and
For assistance, visit www.panasonic.ca/english/support
9
Setup
HNS103C_(en-en)_0224_ver.020.pdf
9
2015/02/24
15:14:55