Panasonic KX-TGA273S C-r H-s For Kxtg2700 - Page 3

Getting Started Section 1 1-F Battery Charge Place the handset on the charger and charge for about 15 hours before initial use. •The unit beeps once, the CHARGE indicator lights, and "Charging" is displayed. CHARGE Indicator •Recharge the battery when: - "Recharge battery" is displayed, - " " flashes on the display, or - the handset beeps intermittently while it is in use. •If the battery has been discharged, the handset will display "Charge for 15HRS" and " " when you place the handset on the charger. The handset will not work unless the battery is charged. Keep charging. 1-G Handset Registration Battery information After your Panasonic battery is fully charged: Operation Operating time While in use (TALK) Up to 4.5 hours While not in use (Standby) While using Reception Booster mode Up to 11 days* Up to 3.5 hours *When using 2-Way Radio mode: Up to 12 hours (Standby) •Clean the charge contacts of the handset and the charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. A nickel cadmium battery that is recyclable powers the product you have purchased. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery. This handset must be registered to a KX-TG2700/KX-TG2720/ KX-TG2730/KX-TG2740/KX-TG2750/KX-TG2770/KX-FPG381 base unit. The handset will be assigned an extension number at registration. The KX-TGA273S will not work without the Panasonic cordless phone systems: KX-TG2700/KX-TG2720/KX-TG2730/KX-TG2740/ KX-TG2750/KX-TG2770/KX-FPG381 [-] Press MUTE on base unit, then OK on handset to register handset O K Soft Key ( OK ) [MUTE] Button and Indicator •Base unit model shown here is KX-TG2770. The MUTE button location varies according to the base unit model. Only one handset can be registered at a time. Make sure the base unit and the other handsets are not being used. Registration must be completed within 1 minute. The handset display shows the instructions as shown on the right. 1 Base unit: Press [MUTE]. • The MUTE indicator flashes. Press MUTE on base unit, then OK on handset to register handset OK 2 Handset: #Press the soft key ( OK ). $Wait until a long beep sounds and the display shows the registered number. •Registration is complete. Ex. Extension number 2 SP PRIVACY [2] Handset [2] Registered •The registered number "[1]" to "[8]" is shown on the top right of the display. •You can stop registration by pressing [OFF] on the handset and pressing [MUTE] on the base unit. •To cancel the handset's registration, please see the base unit Operating Instructions. 1-H Setting Time The charger unit has a 12-hour clock (monthly accuracy ±30 seconds). After the AC adaptor is connected, the display shows " ". It is normal. Follow the steps on the right to set the time. [OFF] [-, TUNE/CLOCK] [TIME SET] [+, TUNE/CLOCK] 1 Press and hold [TIME SET] until the time flashes. 2 Adjust the time by pressing [-, TUNE/CLOCK] or [+, TUNE/CLOCK]. • Pressing [-] or [+] decreases or increases the time in one-minute units. • Pressing and holding [-] or [+] decreases or increases the time faster. 3 Press [TIME SET] to set the time. • The time stops flashing. Ex. 3:30PM is set. •You can exit time setting mode any time by pressing [OFF]. •If a power failure occurs, the display will show " " for about 10 minutes, then it will become blank. After power returns, " " will be displayed. The clock memory will be lost. Set the time. The radio alarm and buzzer alarm memory will be retained for about 10 minutes during a power failure (4-A, 4-B). For assistance, please call: 1-800-211-PANA(7262)