Panasonic PT52LCX16 PT52LCX16 User Guide - Page 25

Basic Operation, First Time Setup - turning off

Get Panasonic PT52LCX16 - MULTI MEDIA DISPLAY PDF manuals and user guides View all Panasonic PT52LCX16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

First Time Setup 2 For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures displayed on-screen for setting up the features. Language The language of the on-screen display is set to English as the factory setting. You can select English, Spanish or French as the 3 on-screen displays language. 1 Press to select "Language". Press to display Language screen. First time setup Language 4 Auto program 2 Press to select "English," "Español" or "Français". Language Language ◄ English ► Press to select "ANT In". Press to select "Cable" or "Antenna". Auto program ANT In ◄ Cable ► Mode All Start scan Press to select Mode. Press to select "All" or "Analog". Auto program ANT In Cable Mode ◄ All ► Start scan Press to select "Start scan". Press to start. Channels available for reception will be set automatically. Auto program ANT In Cable Mode All Start scan 3 Press to go to previous screen. Or, select icon, then press OK for same results. Now scanning analog channel... Progress Auto program You can scan All (Analog and Digital) channels. If needed, follow the menus and procedures displayed on-screen for setting up the features. You can also make the settings in Setup menu. 1 Press to select "Auto program". Press to display Auto program screen. First time setup Language Auto program 5 After Auto program is complete, the unit will return to Manual program mode. To place the channels that were located by auto scan in memory, move the cursor to "Apply" and press OK. (p. 30-31) If OK is not pressed after selecting APPLY, the channels will not be memorized. Notes: • After "Auto program" is completed the unit tunes to the first channel found during "Auto program". • If setup is incomplete, check connection of Antenna/Cable to the RF IN Terminal, then try "Auto program" again. (p. 29) • "Auto program" must be done when you select the input signal for the first time or whenever you change the antenna configuration. • Depending on conditions, "Auto program" may take a while. 25 Basic Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
25
Basic Operation
For your convenience, First Time Set up menu will
be displayed on screen when the set is turned on
for the first time. If needed, follow the menus and
procedures displayed on-screen for setting up the
features.
Auto program
You can scan All (Analog and Digital) channels. If
needed, follow the menus and procedures displayed
on-screen for setting up the features. You can also make
the settings in Setup menu.
Notes:
• After “Auto program” is completed the unit tunes to the first
channel found during “Auto program”.
• If setup is incomplete, check connection of Antenna/Cable to
the RF IN Terminal, then try “Auto program” again. (p. 29)
• “Auto program” must be done when you select the input
signal for the first time or whenever you change the antenna
configuration.
• Depending on conditions, “Auto program” may take a while.
First Time Setup
Language
The language of the on-screen display is set to English
as the factory setting.
You can select English, Spanish or French as the
on-screen displays language.
Press to select “Language”.
Language
◄
English
►
Language
Press to display Language
screen.
1
Press to select “English,”
“Español” or “Français”.
2
3
Press to go to previous
screen. Or, select
icon,
then press OK for same
results.
ANT In
◄
Cable
►
Mode
All
Start scan
Auto program
Press to select “ANT In”.
Press to select “Cable” or
“Antenna”.
2
Press to select Mode.
Press to select “All” or
“Analog”.
3
ANT In
Cable
Mode
◄
All
►
Start scan
Auto program
4
Press to select “Start scan”.
Press to start.
Channels available for
reception will be set
automatically.
ANT In
Cable
Mode
All
Start scan
Auto program
Now scanning analog channel...
Progress
5
After Auto program is complete, the unit will return
to Manual program mode. To place the channels
that were located by auto scan in memory, move the
cursor to “Apply” and press OK. (p. 30-31)
If OK is not pressed after selecting APPLY, the
channels will not be memorized.
Language
Auto program
First time setup
Press to select “Auto
program”.
Press to display Auto program
screen.
1
Language
Auto program
First time setup