Panasonic SAAK340 SAAK240 User Guide - Page 16

ENGLISH DANSK Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to the "Customer Services Directory" on page 18 if you reside in the U.S.A., or refer to the "Product information" on page 15 if you reside in Canada. Reference pages are shown as black circled numbers 4. Common problems Although the unit is in standby mode, the Turn off the demo function. 5 display lights up and changes continuously. If you set the clock, demo function will be turned off automatically. $ No sound. Sound stops. Turn the volume up. Switch off the unit, determine and correct the cause, then switch the unit on. Causes include shorting of the positive and negative speaker wires, straining of the speakers through excessive volume or power, and using the unit in a hot environment. Sound is unfixed, reversed or comes from Check the speaker connections. 4 one speaker only. Humming heard during play. An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away from this unit's cables. "ERROR" is displayed. Incorrect operation performed. Read the instructions and try again. "- -:- -" appears on the display at standby mode. You plugged the AC power supply cord in for the first time or there was a power failure recently. Set the time. $ "F61" is displayed. Check and correct the speaker cords connection. 4 If this does not fix the problem, there is a power supply problem. Consult the dealer. Listening to the radio Noise is heard. The stereo indicator flickers or doesn't light. Sound is distorted. A beat sound is heard. A low hum is heard during AM broadcast. Use an outdoor antenna. 4 Turn the TV off or separate it from the unit. Separate the antenna from other cables and cords. When there is a television set nearby The picture on the TV disappears or stripes appear on the screen. The location and orientation of the antenna are incorrect. If you are using an indoor antenna, change to an outdoor antenna. The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from the unit. Using the cassette deck Poor quality sound. Recording is not possible. Clean the heads. & If the erasure prevention tabs have been removed, cover the holes with adhesive tape. " Playing discs The display is wrong or play won't start. The disc may be upside down. ! Wipe the disc. Replace the disc if it is scratched, warped, or non-standard. Condensation may have formed inside the unit due to a sudden change in temperature. Wait for about an hour for it to clear and try again. The total number of tracks displayed The disc may be scratched, or its data may be defective. Replace the disc. differs each time the same disc is inserted. Unusual sound is heard. CD-RW cannot be read. The disc was incompletely formatted. Use the recording equipment to fully format the disc before recording. "VBR-" is displayed instead of the remaining play time. The unit cannot display the remaining play time for variable bit rate (VBR) tracks. Disc trays Disc tray(s) cannot open. "CHGR ERR " is displayed. Press [y/I, POWER] to release the jammed tray(s) as the unit will switch off. Switch it on again and the tray(s) will initialize to the previous tray(s) condition. If this still does not fix the problem, please consult the dealer. Remote control Remote control doesn't work. Check that the batteries are inserted correctly. 5 Replace the batteries if they are worn. FRANÇAIS LANG - 4 LANG - 5 16 RQT8043 RQTV0061 Memory reset (Initialization) When the following situations occur, refer to the instructions below to reset the memory: • There is no response when buttons are pressed. • You want to clear and reset the memory contents. To reset memory 1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2) 2 While pressing and holding down [y/I, POWER] on the main unit, reconnect the AC power supply cord. appears on the display. 3 Release [y/I, POWER]. All the settings are returned to the factory preset. You will need to reset the memory items.