Panasonic SC-PMX150 Owners Manual - Page 11

About Bluetooth® Panasonic bears no responsibility for data and/or information that is compromised during a wireless transmission. Frequency band used • This system uses the 2.4 GHz frequency band. Certification of this device • This system conforms to frequency restrictions and has received certification based on frequency laws. Thus, a wireless permit is not necessary. • The actions below are punishable by law in some countries: - Taking apart or modifying this system. - Removing specification indications. Restrictions of use • Wireless transmission and/or usage with all Bluetooth® equipped devices is not guaranteed. • All devices must conform to standards set by Bluetooth SIG, Inc. • Depending on the specifications and settings of a device, it can fail to connect or some operations can be different. • This system supports Bluetooth® security features. But depending on the operating environment and/or settings, this security is possibly not sufficient. Transmit data wirelessly to this system with caution. • This system cannot transmit data to a Bluetooth® device. Range of use • Use this device at a maximum range of 10 m (33 ft). The range can decrease depending on the environment, obstacles or interference. Interference from other devices • This system may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference if this system is located too close to other Bluetooth® devices or the devices that use the 2.4 GHz band. • This system may not function properly if radio waves from a nearby broadcasting station, etc. is too strong. Intended usage • This system is for normal, general use only. • Do not use this system near an equipment or in an environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc). Bluetooth® operations By using the Bluetooth® connection, you can listen to the sound from the Bluetooth® audio device from this system wirelessly. • Refer to the operating instructions of the Bluetooth® device for details. Connecting via Bluetooth® menu Preparation • Turn on the Bluetooth® feature of the device and place the device near this unit. Pairing with Bluetooth® devices 1 Press [ ] to select "BLUETOOTH". If "Pairing" is indicated on the display, go to step 3. 2 Press [PLAY MENU] to select "Pairing" and then press [OK]. • Alternatively, press and hold [ -PAIRING] on the unit. 3 Select "SC-PMX150" from the Bluetooth® device's Bluetooth® menu. • The MAC address (e.g., 6C:5A:B5:B3:1D:0F) may be displayed before "SC-PMX150" is displayed. • The name of the connected device is indicated on the display for a few seconds. 4 Start playback on the Bluetooth® device. Connecting a paired Bluetooth® device 1 Press [ ] to select "BLUETOOTH". "Ready" is indicated on the display. 2 Select "SC-PMX150" from the Bluetooth® device's Bluetooth® menu. The name of the connected device is indicated on the display for a few seconds. 3 Start playback on the Bluetooth® device. Note: • If prompted for the passkey, input "0000". • You can register up to 8 devices with this unit. If a 9th device is paired, the device that has not been used for the longest will be replaced. • This unit can only be connected to one device at a time. • When "BLUETOOTH" is selected as the source, this unit will automatically try and connect to the last connected Bluetooth® device. ("Linking" is indicated on the display during this process.) If the connection attempt fails, try to establish a connection again. Bluetooth® transmission mode You can change the transmission mode to prioritize transmission quality or sound quality. Preparation • Press [ ] to select "BLUETOOTH". • If a Bluetooth® device is already connected, disconnect it. 1 Press [PLAY MENU] repeatedly to select "Link Mode". 2 Press [2, 1] to select the mode and then press [OK]. Mode 1: Emphasis on connectivity Mode 2: Emphasis on sound quality Note: • Select "Mode 1" if the sound is interrupted. • When enjoying video contents with this function, the video and audio output may not be synchronized. In this case, select "Mode 1". • The factory default is "Mode 2". 11 TQBJ0996