Panasonic SC-PMX150 Owners Manual - Page 6

TQBJ0996 Network settings You can stream music from an iOS device (iPhone/iPad/ iPod), an Android™ device or a PC (Mac/Windows) to this system's speakers by using the Qualcomm® AllPlay™ smart media platform or AirPlay. To use these features, this system must join the same network as the compatible device. Qualcomm® AllPlay™ is a product of Qualcomm Technologies, Inc. • Please update the system's firmware after the network settings are complete. (> 16) Choose a network setting method from the following. Wireless LAN connection Method 1: "Using the WAC (Wireless Accessory Configuration)" (> right) • If you are using an iPhone/iPad/iPod touch (iOS version 7.0 or later), or Mac (OS X 10.9 or later, with AirPort Utility 6.3.1 or later), you can send its Wi-Fi configuration to this system. Method 2: "Using the app "Panasonic Music Streaming"" (> right) • You can make the wireless network settings with the app, "Panasonic Music Streaming" (free of charge). Method 3: "Using an Internet browser" (> 7) • You can access this unit's network settings from the Internet browser on your smartphone or PC, etc. Method 4: "Using WPS (Wi-Fi Protected Setup™)" (> 8) • If your wireless router supports WPS, you can set up a connection by either pressing the WPS button, or entering the WPS PIN code. Wired LAN connection Method 5: "Using a LAN cable" (> 8) 6 • You can make a stable connection to the network with a LAN cable. Note: • The setting will be canceled after the set time limit. In that case, try the setting again. To cancel this setting in the middle, press [∫]. Wireless LAN connection This system has built-in Wi-Fi® and can be connected to a wireless router. Preparation • Place this system as close to the wireless router as possible. • Do not connect a LAN cable. Doing so will disable the Wi-Fi® function. • Point the antenna on the rear of the main unit up as shown in the figure. • Do not perform the following: - Tilting the antenna forward or backwards when it is pointing up - Applying too much force to the antenna - Carrying this unit by holding the antenna Method 1: Using the WAC (Wireless Accessory Configuration) • The following explanations are based on an iPhone. 1 Turn this system on. 2 Connect the iPhone to your home wireless network. 3 Press [RADIO, EXT-IN] on the remote control repeatedly to select "NETWORK". • When "WAC Mode" is indicated on the display, proceed to step 4. - If the display stays at "NETWORK", perform the operation for network reset. (> 17) 4 Go to Wi-Fi settings on your iPhone. Settings Wi-Fi settings 5 Select "Panasonic PMX150 under the "SET UP NEW AIRPLAY SPEAKER...". • " " stands for a character that is unique to each set. 6 The "AirPlay Setup" screen appears on your iPhone. • This system will be displayed as "Panasonic PMX150"*. * To change the name, enter a new name to replace the existing one. You can also do the renaming after the network connection is set up. (> 8, "To make network-related settings") • You can set a password for this system under "SPEAKER PASSWORD". (You will need this password if you make network settings by Internet browser next time.) 7 Select "Next" to apply the settings. • On the main unit's display, "Success" appears when the connection is established. (" displayed.) " will be Method 2: Using the app "Panasonic Music Streaming" You can also refer to the supplied "Wi-Fi® QUICK SETUP GUIDE". 1 Download the app "Panasonic Music Streaming" (free of charge) on your smartphone/tablet. (Always use the latest version of the app.) • [iOS] : App Store • [Android] : Google Play™ 2 Start the app and follow the on-screen instructions. 3 Check that the connection has completed. • On the unit's display, "Success" appears when the connection is established. (" " will be displayed.) - If "Fail" is displayed press [OK], check the network name (SSID) and the password, and then try the setting again.