Panasonic SL-1000 Owners Manual - Page 14
Pitch control, Operation and display of the control unit
View all Panasonic SL-1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ Pitch control (fine adjustment to pitch) 1 Press [-] or [+] on the control unit to make adjustment. z The pitch can be set within approximately ±16% of the currently set turntable speed [33/45/78]. z The current set value appears on the display of the control unit. The display differs depending on the display mode. (Switching the display mode 27) z The turntable speed changes each time the pitch is set while the turntable is rotating. *Pressing the button increases or decreases the value. *Holding the button down accelerates the increase or decrease. When the display mode is "Turntable speed setting" The specified turntable speed 33 38.67 ・・ The adjusted value (turntable speed) z The value to two decimal places is displayed. z The turntable speed can be adjusted in increments of ±0.01 turn. [+] ↑ 33 33.34 [+] ↑ 33 33.33 [ー] 33 33.32 ・・ [ー] 33 28.00 When the display mode is "Pitch setting" The specified turntable speed 33 + 16.0% ・・ The adjusted value (percentage) (Initial setting) [+] ↑ 33 + 0.1% [+] ↑ 33 0.0% z The value to one decimal place is displayed. z The pitch can be adjusted in increments of ±0.1%. 26 (26) English [ー] 33 - 0.1% ・・ [ー] 33 - 16.0% To return to the prescribed turntable speed Press [RESET] on the control unit. The value immediately returns to the prescribed turntable speed. (331/3, 45 or 78.26 rpm) *The display of the control unit shows the prescribed setting. The turntable speed becomes the prescribed turntable speed in the turntable speed setting mode and 0.0% in the pitch setting mode. (Display mode: Turntable speed setting) 33 33.33 (Display mode: Pitch setting) 33 0.0% Speed selector button indicators of the main unit during pitch control STARTɾSTOP Indicators 33 45 78 z Blue LED on: Without pitch control (0.0%) z Orange LED on: During pitch control Note z The pitch can be set for each turntable speed. z Turning off the power button cancels the pitch control setting. Turning on the power button again returns the value to the initial setting. Operation and display of the control unit ↑ ↑ Turntable speed setting 1 Press [33/45/78] on the control unit. Each time [33/45/78] is pressed, the turntable speed changes in order of "33" → "45" → "78" → "33" → ... z The turntable speed changes each time the pitch is set while the turntable is rotating. 33 33.33 (331/3 turns) 45 45.00 (45 turns) 78 78.26 (78 turns) The specified turntable speed The adjusted value (turntable speed) Switching the display mode 1 Press [DISPLAY] on the control unit. Each time [DISPLAY] is pressed, the display mode changes in order of "turntable speed setting" → "Pitch setting" → "Turntable speed measurement" → "Turntable speed setting" → ... 33 33.33 (Turntable speed setting) 33 0.0% (Pitch setting) (Turntable 33 33.33 rpm speed measurement) (See below.) Turntable speed measurement The actual turntable speed can be measured in this display mode. Switch the display mode (see above) to enter this mode. z "rpm" appears after the numerical value. z "--.-- rpm" appears when the turntable has stopped. 33 --.-- rpm (Stop state) 33 33.33 rpm (During rotation) Operation during "Turntable speed measurement" Operating the buttons as below changes the display mode to "Turntable speed setting" allowing you to make the setting. *The display mode returns to "Turntable speed measurement" if no operation is performed within three seconds. · [-]/[+]: The pitch can be adjusted. ( 26) · [RESET]: The value immediately returns to the prescribed turntable speed. · [33/45/78]: The turntable speed changes each time the button is pressed. Note z An averaged value is displayed. 27 (27) English Playing back