Panasonic SL-1000 Owners Manual - Page 15
Maintenance, Operation and display of the control unit
View all Panasonic SL-1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Operation and display of the control unit (continued) ↑ ↑ ↑ ↑ ↑ ↑ Display dimmer setting The display dimmer will be activated if the control unit is not operated for 20 seconds. There are four dimming patterns. 1 On the control unit, hold [RESET] down and press [DISPLAY]. z The dimmer setting is displayed. 2 Press [DISPLAY] on the control unit. The setting changes each time [DISPLAY] is pressed. (See below.) z The display returns to the original display if no operation is performed within three seconds. 33 33.33 [RESET][DISPLAY] Display OFF [DISPLAY] Dimmer OFF [DISPLAY] Dimmer 1 [DISPLAY] Dimmer 2 (Initial setting) Display Display dimmer when no operation is performed for 20 seconds Brightness is reduced by one level. ⇒ (No operation for further five seconds) Display OFF ⇒ Brightness is reduced by two levels. ⇒ (No operation for further five seconds) ⇒ Off Dimmer OFF No dimming (Always on) Dimmer 1 Brightness is reduced by one level. Dimmer 2 Brightness is reduced by two levels. z After setting, brightness is immediately adjusted to the set value. The display is immediately turned off if "Display OFF" is selected. z Operating a button (any button other than the power button) on the control unit while the dimmer is active returns the display to full brightness. Note z The setting is saved. When the power is turned on the next time, the setting when the power was turned off last will be recovered. 28 (28) English Adjusting the torque to rotate the turntable at a constant speed Press [START·STOP] and then adjust the torque (rotational force) at five levels to rotate the turntable at a constant speed. 1 On the control unit, hold [RESET] down and press [-] and [+] simultaneously. z The torque setting is displayed. 2 Press [-] or [+] on the control unit to make adjustment. z Select one of the five levels from "TORQUE1" to "TORQUE5". Pressing the button increases or decreases the value. z Use the table below as a guide. z The display returns to the original display if no operation is performed within three seconds. 33 33.33 [RESET TORQUE 5 (Initial setting) [+]↑ [-] TORQUE 1 Display TORQUE5 TORQUE4 TORQUE3 TORQUE2 TORQUE1 Torque to rotate at a constant speed Maximum (Initial setting) Minimum Note z The setting is saved. When the power is turned on the next time, the setting when the power was turned off last will be recovered. Maintenance Care of the parts Thoroughly clean dust off the stylus and record. z Take off the head shell with the cartridge and clean the stylus using a soft brush. Brush from the base to the tip. z Use a record cleaner to keep your records clean. Head shell terminals Wipe the head shell terminals occasionally. Wipe the head shell terminals with a soft cloth and fit the head shell to the tone arm. Turn the amplifier volume down or turn the amplifier off before fitting or removing the head shell. Damage to your speakers can occur if the head shell is moved while the volume is turned up. Moving the unit Repackage the unit in the packaging it came in. ( 12) Keep the packaging materials after taking out the goods. If you no longer have the packaging, do the following: z Take off the turntable and turntable mat and carefully wrap them. z Remove the head shell and balance weight from the tone arm and carefully wrap them. z Clamp the tone arm with the arm clamp and tape it in place. z Carefully wrap the main unit in a blanket or paper. Repackaging Cleaning the dust cover and cabinet Wipe the dust cover and cabinet with a soft cloth. When dirt is heavy, wring a wet cloth tightly to wipe the dirt, and then wipe it with a soft cloth. z Do not use solvents including benzene, thinner, alcohol, kitchen detergent, a chemical wiper, etc. This might cause the exterior case to be deformed or the coating to come off. z Do not wipe the dust cover while playing a record. This can cause static electricity. This static can cause the tone arm to be attracted towards the dust cover. Before repackaging, remove the balance weight and insert the tone arm support under the tone arm. WEEE symbol Disposal of the product outside the EU countries This symbol is valid within the EU only. Contact a local governmental office or your dealer to confirm a right manner of disposal. 29 (29) English Maintenance Playing back