Panasonic SL-1000 Owners Manual - Page 9

Connections and installation

Get Panasonic SL-1000 PDF manuals and user guides View all Panasonic SL-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connections and installation z Turn off all units and disconnect the AC mains lead from the socket before making any connections. z Connect the AC mains lead only after all other connections are completed. z Be sure to connect the PHONO earth lead. Otherwise mains hum may occur. z Refer also to the instruction manual of the connected device. Connecting the output terminal and AC IN terminal / Connecting the control unit 1 Connect a commercially available phono cable to the output terminal. 2 Connect the control unit connection cable by inserting it until it clicks into place. Connecting the pre-main amplifier and component / Connecting the power plug and earth ground 4 Connect the commercially available phono cable to the PHONO input terminals of the amplifier connected to the unit. z You will not have adequate volume or sound quality if the connected amplifier has no PHONO input terminals. 3 Connect the AC mains lead. 5 Connect the power plug and earth ground. z Confirm the wattage of the AC outlet on the connected equipment before using it for this unit. (This unit consumes 10 W.) Note z The operation switch does not separate entire unit from mains even if in "OFF" position. Remove the plug from the mains socket if you will not be using the unit for an extended period of time. Place the unit so that the plug can be easily removed. 16 (16) English Back of main unit Chassis ground Amplifier (not included) 1)0/&4 7" 70-6.& */1654&-&$503 1)0/0 &"35) 1)0/0 4 R L 1 PHONO cable (not included) ● Use a 5-pin straight phono cable. Control unit connection cable 2 Back of Control unit 3 To a household mains socket AC mains lead ※ Chassis ground Earth lead with lug M3 screw Basically, there is no need to connect the chassis ground. If you are concerned about the noise, connect as described below. The noise may decrease though it depends on your environment of use. ① Using a commercially available M3 screw, attach an earth lead with lug to the chassis ground. ② Connect the earth lead to the earth terminal on the amplifier. M3 screw (coarse thread) 13 mm or less ● Use a conductive screw. 12 mm or less 17 (17) English Getting started

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
Getting started
English
(16)
English
(17)
Connections and installation
z
Turn off all units and disconnect the AC mains lead from the socket before making any
connections.
z
Connect the AC mains lead only after all other connections are completed.
z
Be sure to connect the PHONO earth lead. Otherwise mains hum may occur.
z
Refer also to the instruction manual of the connected device.
z
The operation switch does not separate entire unit from mains even if in “OFF“ position.
Remove the plug from the mains socket if you will not be using the unit for an extended period of
time. Place the unit so that the plug can be easily removed.
Note
16
17
2
Connect the control unit
connection cable by inserting it
until it clicks into place.
1
Connect a commercially available
phono cable to the output
terminal.
3
Connect the AC mains lead.
4
Connect the commercially
available phono cable to the
PHONO input terminals of the
amplifier connected to the unit.
z
You will not have adequate volume or
sound quality if the connected amplifier
has no PHONO input terminals.
5
Connect the power plug and
earth ground.
z
Confirm the wattage of the AC outlet on
the connected equipment before using it
for this unit.
(This unit consumes 10 W.)
Connecting the pre-main
amplifier and component /
Connecting the power plug
and earth ground
Connecting the output
terminal and AC IN terminal /
Connecting the control unit
PHONO
PHONO
EARTH
L
R
Back of main unit
Chassis ground
AC mains lead
PHONO cable (not included)
Control unit connection cable
Back of Control unit
Amplifier
(not included)
To a household mains socket
4
2
3
1
●
Use a 5-pin straight phono cable.
Basically, there is no need to connect the chassis ground.
If you are concerned about the noise, connect as described
below. The noise may decrease though it depends on your
environment of use.
①
Using a commercially available M3 screw, attach an earth
lead with lug to the chassis ground.
②
Connect the earth lead to the earth terminal on the
amplifier.
※
Chassis ground
●
Use a conductive screw.
13 mm or less
12 mm or less
M3 screw
(coarse
thread)
Earth lead
with lug
M3 screw