Panasonic WVCU650 Operating Instructions - Page 18

SETUP PROCEDURES (HARDWARE), Setup Procedures, MODE Switch Setting, CONTROLLER NO. Switch Setting

Get Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM PDF manuals and user guides
UPC - 791871504277
View all Panasonic WVCU650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

SETUP PROCEDURES (HARDWARE) ■ Setup Procedures Perform the setup as follows. 1. Set the MODE switches. You will set up the communication mode and line termination ON/OFF of RS-485 communication. (Refer to MODE Switch Setting.) 2. Set CONTROLLER NO. switches. You will perform this setting when using two or more system controllers in daisy chain connections. (Refer to CONTROLLER NO. Setting.) 3. Perform WV-CU650 setups after entering the administrator password. You will perform the settings concerning password and communication between system controllers and other system units, etc. (Refer to p. 19.) Note: Before performing WV-CU650 setups, you need to log into the system by entering the administrator password. (Refer to p. 19.) ■ MODE Switch Setting You will perform the setting of the MODE switches at the rear panel. Notes: • Before the setting, turn off the system controller. (Refer to p. 27 Power-off.) • Do not move the MODE switches to positions other than described in these illustrations. That may cause malfunction. ● Setting for PS·Data Mode If using only one system controller Set the MODE Switch #5 to ON. 1 2 3 4 5 67 8 OFF ON MODE Switch #5 (Line termination switch) If using two or more system controllers in daisy chain connections 1. Set the MODE Switch #5 of the system controller at the chain end to ON. 18 2. Set the Line termination switch of other system controllers to OFF. 1 2 3 4 5 67 8 OFF ON System units Line termination ON Line termination OFF Line termination OFF Line termination OFF Line termination ON ● Setting for Terminal Mode Set the MODE Switch #1 and #5 to ON. 1 2 3 4 5 67 8 OFF ON Note: Refer to the following document for details on connections and operations. Addendum for WV-CU650 and WJ-SX150 Series ■ CONTROLLER NO. Switch Setting You will determine controller-number settings by moving the CONTROLLER NO. switch at the rear panel. If using only one system controller Maintain the switch setting as "1 (factory default position)". If using two or more system controllers in daisy chain connections Up to 4 system controllers are connectable in the system. To avoid conflict, set the unique number for each system controller. 901 CONTROLLER No. Notes: • "0" and "9" are reserved numbers. They cannot be set for controller numbers. • One of the system controllers must be set to "1". 78 23 456

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
18
2. Set the Line termination switch of other system con-
trollers to OFF.
●
Setting for Terminal Mode
Set the MODE Switch #1 and #5 to ON.
Note:
Refer to the following document for details on con-
nections and operations.
Addendum for WV-CU650 and WJ-SX150 Series
■
CONTROLLER NO. Switch
Setting
You will determine controller-number settings by moving
the CONTROLLER NO. switch at the rear panel.
If using only one system controller
Maintain the switch setting as “1 (factory default position)”.
If using two or more system controllers in
daisy chain connections
Up to 4 system controllers are connectable in the system.
To avoid conflict, set the unique number for each system
controller.
Notes:
• “0” and “9” are reserved numbers. They cannot be set
for controller numbers.
•
One of the system controllers must be set to "1".
System units
Line termination ON
Line termination OFF
Line termination OFF
Line termination OFF
Line termination ON
CONTROLLER No.
0
9
8
7
6
5
4
3
2
1
SETUP PROCEDURES (HARDWARE)
■
Setup Procedures
Perform the setup as follows.
1.
Set the MODE switches.
You will set up the communication mode and line termi-
nation ON/OFF of RS-485 communication. (Refer to
MODE Switch Setting.)
2.
Set CONTROLLER NO. switches.
You will perform this setting when using two or more
system controllers in daisy chain connections. (Refer to
CONTROLLER NO. Setting.)
3.
Perform WV-CU650 setups after entering the
administrator password.
You will perform the settings concerning password and
communication between system controllers and other
system units, etc. (Refer to p. 19.)
Note:
Before performing WV-CU650 setups, you need to
log into the system by entering the administrator pass-
word. (Refer to p. 19.)
■
MODE Switch Setting
You will perform the setting of the MODE switches at the
rear panel.
Notes:
• Before the setting, turn off the system controller. (Refer
to p. 27 Power-off.)
•
Do not move the MODE switches to positions other than
described in these illustrations. That may cause mal-
function.
●
Setting for PS·Data Mode
If using only one system controller
Set the MODE Switch #5 to ON.
If using two or more system controllers in
daisy chain connections
1. Set the MODE Switch #5 of the system controller at the
chain end to ON.
1
2
3
4
5
6
7
8
OFF
ON
MODE Switch #5 (Line termination switch)
1
2
3
4
5
6
7
8
OFF
ON
1
2
3
4
5
6
7
8
OFF
ON