Pioneer AVIC-D1 Other Manual - Page 13

Violet/white REVERSEGEAR SIGNAL INPUT - camera

Page 13 highlights

English Español Extension lead (for speed signal) Note: Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function. This product Power cord Violet/white (REVERSEGEAR SIGNAL INPUT) This is connected so that the navigation system can detect whether the vehicle is moving forwards or backwards. Connect the violet/white lead to the lead whose voltage changes when the shift lever is put in reverse. Unless connected, the sensor may not detect your vehicle traveling forward/backward properly, and thus the position of your vehicle detected by the sensor may be misaligned from the actual position. Note: When you use the ND-PG1 speed pulse generator (sold separately), please make sure to connect this lead. When you use a rear view camera, please make sure to connect this lead. Otherwise you cannot switch to rear view camera picture. See Page 15. For information on other leads See Page 9. Connection method Clamp the reversing lamp lead. Clamp firmly with needle-nosed pliers. Deutsch Français Italiano Nederlands Be sure to use only the supplied extension lead. Use of another lead could cause fire, smoke and/or damage this product. Fuse resistor Extension lead (for reverse signal) 5 m (16 ft. 5 in.) Check the position of your vehicle's reversing lamp (the one that lights up when the shift lever is in reverse [R]) and find the reversing lamp lead in the trunk. Reversing lamp lead 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54

Be sure to use only the supplied extension lead. Use of another
lead could cause fire, smoke and/or damage this product.
12
English
Español
Deutsch
Français
Italiano
Nederlands
Note:
Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied manuals of both prod-
ucts and connect cords that have the same function.
Power cord
Violet/white (REVERSEGEAR SIGNAL INPUT)
This is connected so that the navigation system can
detect whether the vehicle is moving forwards or
backwards. Connect the violet/white lead to the
lead whose voltage changes when the shift lever is
put in reverse. Unless connected, the sensor may
not detect your vehicle traveling forward/backward
properly, and thus the position of your vehicle
detected by the sensor may be misaligned from the
actual position.
Note:
When you use the ND-PG1 speed pulse
generator (sold separately), please make sure
to connect this lead.
When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to rear view camera picture.
See Page 15.
Connection method
Clamp the reversing lamp lead.
Clamp firmly with
needle-nosed pliers.
Reversing
lamp lead
Fuse resistor
Check the position of your vehicle
s
reversing lamp (the one that lights up
when the shift lever is in reverse [R])
and find the reversing lamp lead in the
trunk.
This product
Extension lead
(for reverse signal)
Extension lead (for speed signal)
For information on other leads
5 m (16 ft. 5 in.)
See Page 9.