Pioneer AVIC-D1 Other Manual - Page 6

Before installing this product, To prevent damage - owners manual

Get Pioneer AVIC-D1 PDF manuals and user guides
UPC - 012562739496
View all Pioneer AVIC-D1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Connecting the System Before installing this product • This product is for vehicles with a 12-volt battery and negative grounding. Check the battery voltage of your vehicle before installation. • To avoid shorts in the electrical system, be sure to disconnect the (-) battery cable before beginning installation. To prevent damage When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder. • When disconnecting a connector, pull the connector itself. Do not pull the lead, as you may pull it out of the connector. • This product cannot be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch. F ACC O F O OF OF N STAR N STAR T T ACC position No ACC position • When connecting the blue lead to the auto antenna and using the auto antenna function, the vehicle's antenna can be stowed by following the instructions below. - In the INITIAL menu, select "RADIO" for "AUTO ANTENNA" and change the source from radio to another source - Turn the source off - Turn off the ignition switch (ACC OFF) For more detailed information on changing the "AUTO ANTENNA" mode, refer to "Switching the auto antenna setting" in the "Operation Manual". • To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especially important to insulate all unused speaker leads, which if left uncovered may cause a short circuit. • Attach the connectors of the same color to the corresponding colored port, i.e., blue connector to the blue port, black to black, etc. • Refer to the owner's manual for details on connecting the power amp and other units, then make connections accordingly. • Since a unique BPTL circuit is employed, do not directly ground the ≠ side of the speaker lead or connect the ≠ sides of the speaker leads together. Be sure to connect the ≠ side of the speaker lead to the ≠ side of the speaker lead on this product. • If the RCA pin jack on this product will not be used, do not remove the caps attached to the end of the connector. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
5
Connecting the System
Before installing this product
•
This product is for vehicles with a 12-volt battery and negative grounding. Check the
battery voltage of your vehicle before installation.
To prevent damage
When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.
•
When disconnecting a connector, pull the connector itself. Do not pull the lead, as you
may pull it out of the connector.
•
This product cannot be installed in a vehicle that does not have an ACC (accessory)
position on the ignition switch.
•
To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especial-
ly important to insulate all unused speaker leads, which if left uncovered may cause a
short circuit.
•
Attach the connectors of the same color to the corresponding colored port, i.e., blue con-
nector to the blue port, black to black, etc.
•
Refer to the owner’s manual for details on connecting the power amp and other units,
then make connections accordingly.
•
Since a unique BPTL circuit is employed, do not directly ground the
≠
side of the
speaker lead or connect the
≠
sides of the speaker leads together. Be sure to connect the
≠
side of the speaker lead to the
≠
side of the speaker lead on this product.
•
If the RCA pin jack on this product will not be used, do not remove the caps attached to
the end of the connector.
•
When connecting the blue lead to the auto antenna and using the auto antenna function,
the vehicle’s antenna can be stowed by following the instructions below.
– In the INITIAL menu, select “
RADIO
” for “
AUTO ANTENNA
” and change the
source from radio to another source
– Turn the source off
– Turn off the ignition switch (ACC OFF)
For more detailed information on changing the “
AUTO ANTENNA
” mode, refer to
“Switching the auto antenna setting” in the “Operation Manual”.
No ACC position
ACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
•
To avoid shorts in the electrical sys-
tem, be sure to disconnect the (–)
battery cable before beginning
installation.