Pioneer DJM 600 Owner's Manual - Page 7

CONNECTIONS 2. Connection of Outputs, Microphones, etc. Main microphone Headphones MIC CH-1 CD1/LINE LINE PROFESSIONAL CH-2 CH-3 CD2/LINE PHONO 1 LINE PHONO 2 DJ MIXER DJM-600 CH-4 MASTER LINE SUB MIC /PHONO 3 MONO STEREO POWER MIC LEVEL - ∞ 0dB HI -12dB +12dB MID EQ -12dB +12dB LOW -12dB +12dB TRIM dB 14 10 7 -∞ +9dB 4 HI 2 1 0 -26dB -1 MID -2 +12dB -3 EQ -5 -7 -26dB +12dB -10 LOW -15 -24 -26dB +12dB TRIM dB 14 10 7 -∞ +9dB 4 HI 2 1 0 -26dB -1 MID -2 +12dB -3 EQ -5 -7 -26dB +12dB -10 LOW -15 -24 -26dB +12dB TRIM dB 14 10 7 -∞ +9dB 4 HI 2 1 0 -26dB -1 MID -2 +12dB -3 EQ -5 -7 -26dB +12dB -10 LOW -15 -24 -26dB +12dB TRIM dB 14 10 7 -∞ +9dB 4 HI 2 1 0 -26dB -1 MID -2 +12dB -3 EQ -5 -7 -26dB +12dB -10 LOW -15 -24 -26dB +12dB HEADPHONES CUE MASTER LEVEL dB 14 10 7 4 2 1 0 -1 -2 -3 -5 -7 -10 -15 -24 L R BEAT BEAT EFFECTS SAMPLER 1234 AUTO BPM COUNTER 70-139 BPM 91-180 BPM BPM MASTER 1 2 3 4 MIC PARAMETER1 % BPM mSec 1/2 3/4 1/1 2/1 4/1 1 2 4 8 16 BEAT TALK OVER CH-1 CH-2 CH-3 AUTO BPM COUNTER SELECTOR CH-4 MASTER EFFECTS/SAMPLER 10 HEADPHONES 9 8 MONO SPLIT STEREO 7 6 5 MIXING 4 3 2 1 0 CUE MASTER LEVEL 10 9 8 7 6 5 4 3 2 1 0 CH-1 - ∞ 0dB 23 OFF ON 1 4 THRU SAMPLER PHONES CROSS FADER ASSIGN A 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 CH-2 SAMPLER OFF ON FADER START 1 2 3 OFF ON 2 1 THRU CROSS FADER CURVE 3 4 SAMPLER CROSS FADER ASSIGN B MASTER BALANCE L R BOOTH MONITOR REVERB FRANGER PITCH FILTER SND/RTN TRANS EDIT PAN SINGLE ECHO LOOP DELAY STRETCH AUTO BPM 4 3 REC BEAT SAMPLER MIC CF. A 2 CF. B 1 MASTER CH. SELECT PARAMETER 1 TIME PARAMETER 2 LEVEL/ DEPTH MIN MAX A B - ∞ 0dB ON/OFF TAP DJM-600 Power amplifier (Supports RCA input) RLLR Power amplifier (For booth monitor) Sub-microphone (CH-4's PHONO 3 cannot be used if connecting a sub-microphone.) MASTER BOOTH OUT 1 MONITOR L CH - 4 PHONO 3 LINE L CH - 3 PHONO 2 LINE L CH - 2 PHONO 1 CD 2 /LINE CH - 1 LINE CD 1 /LINE L L R R MASTER LEVEL ATT. R R R SIGNAL GND CH - 2 CH - 1 PLAYER CONTROL 220-230 110-120V -240V VOLTAGE SELECTOR MASTER OUT2 R 2 COLD 3 HOT R L R LR L L 1 GND REC OUT SEND (MONO) RETURN (MONO) CH - 4 SUBMIC XLR terminal polarity is as RL shown in the diagram below. *4 *6 *5 COLD (-) 23 1 HOT (+) GND DJM-600 Power amplifier (Supports XLR input) Cassette deck, etc. External effector *4 MASTER LEVEL ATT. (Master output-level attenuator knob) This knob is used to decrease the output level to protect connected amplifiers and speakers from excessive input. (Attenuation: -∞ to 0dB) *5 Connect if you want to use another device for adjusting sound quality. SEND (output): Connect this to the external effector's input terminal. When using a monaural input effector, connect it to the L channel output. The effector will receive LR-mixed sound. RETURN (input): Connect this to the external effector's output terminal. When using a monaural output effector, connect it to the L channel output. The signals from the effector will be input to both the L and R channels. *6 REC OUT. Outputs sound to the same output source as the master output, without being influenced by the master volume, master balance and MONO switches. 7