Pioneer GM-6500F Owner's Manual - Page 7

About bridged mode, About suitable, specification of speaker, Connecting the speakers, Connecting - 4 channel amplifier

Get Pioneer GM-6500F PDF manuals and user guides View all Pioneer GM-6500F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Connecting the units Section 03 English ! If the system remote control wire of the amplifier is connected to the power terminal via the ignition switch (12 V DC), the amplifier will remain on with the ignition whether the car stereo is on or off, which may exhaust battery if the engine is at rest or idling. ! Install and route the separately sold battery wire as far as possible from the speaker wires. Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as possible from the antenna, antenna cable and tuner. About bridged mode About suitable specification of speaker Ensure speakers conform to the following standards, otherwise there is a risk of fire, smoke or damage. Speaker impedance is 2 W to 8 W, or 4 W to 8 W for two-channel and other bridge connections. Subwoofer Speaker channel Power Four-channel output Nominal input: Min. 60 W Two-channel output Nominal input: Min. 180 W Three-channel Speaker output A Nominal input: Min. 60 W Three-channel Speaker output B Nominal input: Min. 180 W Speaker impedance is max. 4 W, please carefully check. Improper connection to the amplifier may result in malfunction or personal injury due to burns from overheating. For bridged mode for a two-channel amplifier, with a 4 W load, either wire two 8 W speakers in parallel, Left + and Right * (Diagram A) or use a single 4 W speaker. For other amplifiers, please follow the speaker output connection diagram for bridging shown on rear: two 8 W speakers in parallel for a 4 W load or a single 4 W speaker per channel. For any further enquiries, contact your local authorized Pioneer dealer or customer service. Other than subwoofer Speaker channel Power Four-channel output Max. input: Min. 120 W Two-channel output Max. input: Min. 360 W Three-channel Speaker output A Max. input: Min. 120 W Three-channel Speaker output B Max. input: Min. 360 W Connecting the speakers The speaker output mode can be four-channel, three-channel (stereo and mono) or two-channel (stereo or mono). Connect the speaker leads based on the mode and the figures shown below. En 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
!
If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch (12 V DC), the amplifier will re-
main on with the ignition whether the car
stereo is on or off, which may exhaust battery
if the engine is at rest or idling.
!
Install and route the separately sold battery
wire as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away as possible from the anten-
na, antenna cable and tuner.
About bridged mode
Speaker impedance is max. 4
W
, please carefully
check. Improper connection to the amplifier may
result in malfunction or personal injury due to
burns from overheating.
For bridged mode for a two-channel amplifier,
with a 4
W
load, either wire two 8
W
speakers in
parallel, Left
+
and Right
*
(Diagram A) or use a
single 4
W
speaker. For other amplifiers, please
follow the speaker output connection diagram for
bridging shown on rear: two 8
W
speakers in par-
allel for a 4
W
load or a single 4
W
speaker per
channel.
For any further enquiries, contact your local
authorized Pioneer dealer or customer service.
About suitable
specification of speaker
Ensure speakers conform to the following
standards, otherwise there is a risk of fire,
smoke or damage. Speaker impedance is 2
W
to 8
W
, or 4
W
to 8
W
for two-channel and other
bridge connections.
Subwoofer
Speaker channel
Power
Four-channel output
Nominal input:
Min. 60 W
Two-channel output
Nominal input:
Min. 180 W
Three-channel
Speaker output A
Nominal input:
Min. 60 W
Three-channel
Speaker output B
Nominal input:
Min. 180 W
Other than subwoofer
Speaker channel
Power
Four-channel output
Max. input:
Min. 120 W
Two-channel output
Max. input:
Min. 360 W
Three-channel
Speaker output A
Max. input:
Min. 120 W
Three-channel
Speaker output B
Max. input:
Min. 360 W
Connecting the speakers
The speaker output mode can be four-channel,
three-channel (stereo and mono) or two-chan-
nel (stereo or mono). Connect the speaker
leads based on the mode and the figures
shown below.
En
7
English
Section
03
Connecting the units