Pioneer VSX-40 Owner's Manual - Page 52
Press ALC/STANDARD SURR to confirm. - sound problem
View all Pioneer VSX-40 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 52 highlights
10 Additional information Note • Depending on the component, audio output may be limited to the number of channels available from the connected display unit (for example audio output is reduced to 2 channels for a monitor with stereo audio limitations). • If you want to switch the input source, you'll have to switch functions on both the receiver and your display unit. • Since the sound is muted on the display when using the HDMI connection, you must adjust the volume on the display every time you switch input sources. iPod messages 'iPod/USB Error 1 (I/U ERR1)', 'iPod/USB Error 3 (I/U ERR3)' Switch off the receiver and reconnect the iPod to the receiver. If this doesn't seem to work, try resetting your iPod. 'iPod/USB Error 2 (I/U ERR2)' Switch off the receiver and reconnect the iPod to the receiver. If this doesn't seem to work, try resetting your iPod. An iPod not supported by this receiver is connected. Connect the iPod supported by this receiver (see page 27). 'No Track' When there are no tracks in the category selected on the iPod. Select a different category. SIRIUS radio messages 'NO ANT' Antenna is not properly connected. Check that the antenna cable is attached securely. 'CHECK SIRIUS TUNER' SIRIUS Connect tuner is not properly connected. Check that the 8 pin mini DIN cable and AC Adapter are attached securely. 'NO SIG' The SIRIUS signal is too weak at the current location. There is no SIRIUS signal or the SiriusConnect Tuner is connected. 'SUB UPDT' Unit is updating subscription. Wait until the encryption code has been updated. 'UPD ***%' Unit is updating channels. Wait until the encryption code has been updated. 'INVLD CH' Selected channel is not available/does not exist. Select another channel. About iPod/iPhone/iPad Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down BAND, press and hold STANDBY/ON for about two seconds. 3 When you see RESET? appear in the display, press AUTO SURROUND/STREAM DIRECT. OK? shows in the display. 4 Press ALC/STANDARD SURR to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. Important • If the Control with HDMI function is set to ON, you may not be able to reset the unit. In this case, reset either by turning OFF the Control with HDMI function, or by putting the unit into standby mode by turning off the power of all the connected devices, and resetting after the HDMI indicator on the front panel turns off. USB messages 'iPod/USB Error 1 (I/U ERR1)' There is a problem with the signal path from the USB to the receiver. Switch off the receiver and reconnect the USB to the receiver. 'iPod/USB Error 3 (I/U ERR3)' When there is no response from the USB. Switch off the receiver and reconnect the USB to the receiver. 'iPod/USB Error 4 (I/U ERR4)' The power requirements of the USB device are too high for this receiver. Switch off the receiver and reconnect the USB to the receiver. 52 En "Made for iPod," "Made for iPhone" and "Made for iPad" mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. Apple, iPad, iPhone, iPod, iPod shuffle, iPod nano, iPod classic, iPod touch and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.