Pioneer VSX-935 7.2-Channel Network AV Receiver Instruction Manual English - Page 173

North American models, European models, Australian and Asian models, Amplifier

Get Pioneer VSX-935 7.2-Channel Network AV Receiver PDF manuals and user guides View all Pioneer VSX-935 7.2-Channel Network AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

General Specifications Appendix Amplifier Section Rated Output Power Maximum Effective Output Power Dynamic Power (IEC60268-Short-term maximum output power) THD+N (Total Harmonic Distortion + Noise) Input Sensitivity and Impedance Rated RCA Output Level and Impedance Phono Maximum Input Signal Voltage Frequency Response Tone Control Characteristics Signal to Noise Ratio Speaker Impedance Headphone Rated Output Supported impedance of Headphones Headphones Frequency Response North American models With 8 ohm loads, both channels driven, from 20-20,000 Hz; rated 80 watts per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output. (FTC) 170 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD European models Australian and Asian models 7 ch × 135 W at 6 ohms, 1 kHz, 1 ch driven of 1% THD (IEC) 160 W at 6 ohms, 1 kHz, 1 ch driven 7 ch × 160 W at 6 ohms, 1 kHz, 1 ch of 10% THD (JEITA) driven of 10% THD (JEITA) 160 W (3 Ω, Front), 125 W (4 Ω, Front), 85 W (8 Ω, Front) 0.08% (20 Hz - 20,000 Hz, Rated output power) 200 mV/47 kΩ (LINE(RCA)), 3.5 mV/47 kΩ (PHONO MM) PRE OUT (SUBWOOFER ) : 1 V/470 Ω LINE OUT (ZONE 2/ZONE B) : 200 mV/2.2 kΩ 70 mV (MM 1 kHz 0.5%) 10 Hz - 100 kHz/+1 dB, -3 dB (Direct/Pure Direct) ±10 dB, 20 Hz (BASS), ±10 dB, 20 kHz (TREBLE) 106 dB (IHF-A, LINE IN, SP OUT), 80 dB (IHF-A, PHONO IN, SP OUT) 4 Ω - 16 Ω 80 mW + 80 mW (32 Ω, 1 kHz, 10% THD) 8 Ω - 600 Ω 10 Hz - 100 kHz 173

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
173
Appendix
General Specifications
Amplifier Section
North American models
European models
Australian and Asian models
Rated Output Power
With 8 ohm loads, both channels
driven, from 20-20,000 Hz; rated 80
watts per channel minimum RMS
power, with no more than 0.08%
total harmonic distortion from 250
milliwatts to rated output. (FTC)
7 ch × 135 W at 6 ohms, 1 kHz, 1 ch driven of 1% THD (IEC)
Maximum Effective Output Power
170 W at 6 ohms, 1 kHz, 1 ch driven
of 10% THD
160 W at 6 ohms, 1 kHz, 1 ch driven
of 10% THD (JEITA)
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch
driven of 10% THD (JEITA)
Dynamic Power (IEC60268-Short-term
maximum output power)
160 W (3 Ω, Front), 125 W (4 Ω, Front), 85 W (8 Ω, Front)
THD+N (Total Harmonic Distortion + Noise)
0.08% (20 Hz - 20,000 Hz, Rated output power)
Input Sensitivity and Impedance
200 mV/47 kΩ (LINE(RCA)), 3.5 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
PRE OUT (SUBWOOFER ) : 1 V/470 Ω
LINE OUT (ZONE 2/ZONE B) : 200 mV/2.2 kΩ
Phono Maximum Input Signal Voltage
70 mV (MM 1 kHz 0.5%)
Frequency Response
10 Hz - 100 kHz/+1 dB, –3 dB (Direct/Pure Direct)
Tone Control Characteristics
±10 dB, 20 Hz (BASS), ±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
106 dB (IHF-A, LINE IN, SP OUT), 80 dB (IHF-A, PHONO IN, SP OUT)
Speaker Impedance
4 Ω - 16 Ω
Headphone Rated Output
80 mW + 80 mW (32 Ω, 1 kHz, 10% THD)
Supported impedance of Headphones
8 Ω - 600 Ω
Headphones Frequency Response
10 Hz - 100 kHz