ProForm 12.0tt Treadmill English Manual - Page 14

wires. Make sure that the handrail wires J, do not pinch any

Get ProForm 12.0tt Treadmill PDF manuals and user guides View all ProForm 12.0tt Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

10. IMPORTANT: To avoid damaging the Pulse Crossbar (93), do not use power tools and do not overtighten the #10 x 3/4" Screws (9). Orient the Pulse Crossbar (93) as shown. Attach 10 9 86 28 5 J the Pulse Crossbar to the Handrails (86) with two #10 x 3/4" Screws (9) and two #10 Star Washers 93 (5); start both Screws, and then tighten them. Make sure not to pinch the Upright Wire (81) or the handrail wires (J). Next, firmly tighten the four 5/16" x 2 1/2" Screws (28). Then, remove the wire tie (A) from the Upright Wire (81). 9 5J 28 86 81 A 11. H old the console assembly (K) near the Pulse Crossbar (93). Connect the ground wire from the console assembly to the Console Ground Wire (58) on the Pulse Crossbar. Next, set the console assembly (K) on the brackets on the Handrails (86); do not pinch any wires. Make sure that the handrail wires (J) are oriented as shown. Attach the console assembly (K) with the four 5/16" x 3/4" Screws (4) that you removed in step 8 and four 5/16" Star Washers (11); do not fully tighten the Screws yet. 11 J 86 11 4 K 58 93 86 J 11 4 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
14
10.
IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do
not overtighten the #10 x 3/4" Screws (9).
Orient the Pulse Crossbar (93) as shown. Attach
the Pulse Crossbar to the Handrails (86) with two
#10 x 3/4" Screws (9) and two #10 Star Washers
(5);
start both Screws, and then tighten them.
Make sure not to pinch the Upright Wire (81)
or the handrail wires (J).
Next, firmly tighten the four 5/16" x 2 1/2"
Screws (28).
Then, remove the wire tie (A) from the Upright
Wire (81).
10
9
9
5
5
28
28
86
93
86
J
J
81
11.
Hold the console assembly (K) near the Pulse
Crossbar (93). Connect the ground wire from the
console assembly to the Console Ground Wire
(58) on the Pulse Crossbar.
Next, set the console assembly (K) on the brack
-
ets on the Handrails (86);
do not pinch any
wires. Make sure that the handrail wires (J)
are oriented as shown.
Attach the console assembly (K) with the four
5/16" x 3/4" Screws (4) that you removed in step
8 and four 5/16" Star Washers (11);
do not fully
tighten the Screws yet.
11
93
K
11
86
58
4
86
4
11
J
J
A