ProForm 205 Cst Uk Manual - Page 22

Maintenance And Troubleshooting

Get ProForm 205 Cst PDF manuals and user guides View all ProForm 205 Cst manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Regular maintenance is important for optimal performance and to reduce wear. Inspect and properly tighten all parts each time the treadmill is used. Replace any worn parts immediately. Regularly clean the treadmill and keep the walking belt clean and dry. First, press the power switch into the off position and unplug the power cord. Wipe exterior parts of the treadmill with a damp cloth and a small amount of mild soap. IMPORTANT: Do not spray liquids directly onto the treadmill. To avoid damage to the console, keep liquids away from the console. Then, thoroughly dry the treadmill with a soft towel. TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in. c Tripped Reset SYMPTOM: The power turns off during use a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. SYMPTOM: The power does not turn on a. Make sure that the power cord is plugged into a properly earthed outlet (see page 12). If an extension cord is needed, use only a 3-conductor, 14-gauge (2 mm2) cord that is no longer than 5 ft. (1.5 m). b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Remove the key from the console, and then reinsert it. d. If the treadmill still will not run, please see the front cover of this manual. SYMPTOM: The incline of the treadmill does not change correctly a.  Enter the settings mode (see page 18). Press the Stop button once, and then press the Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. When the incline system is calibrated, remove the key from the console. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
22
MAINTENANCE
Regular maintenance is important for optimal per-
formance and to reduce wear. Inspect and properly
tighten all parts each time the treadmill is used.
Replace any worn parts immediately.
Regularly clean the treadmill and keep the walking belt
clean and dry. First,
press the power switch into the
off position and unplug the power cord.
Wipe exte-
rior parts of the treadmill with a damp cloth and a small
amount of mild soap.
IMPORTANT: Do not spray
liquids directly onto the treadmill. To avoid damage
to the console, keep liquids away from the console.
Then, thoroughly dry the treadmill with a soft towel.
TROUBLESHOOTING
Most treadmill problems can be solved by follow
-
ing the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis
-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a.
Make sure that the power cord is plugged into a
properly earthed outlet (see page 12). If an exten-
sion cord is needed, use only a 3-conductor,
14-gauge (2 mm
2
) cord that is no longer than 5 ft.
(1.5 m).
b.
After the power cord has been plugged in, make
sure that the key is inserted into the console.
c.
Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
SYMPTOM: The power turns off during use
a.
Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b.
Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c.
Remove the key from the console, and then
reinsert it.
d.
If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The incline of the treadmill does not
change correctly
a.
Enter the settings mode (see page 18). Press
the Stop button once, and then press the Incline
increase or decrease button. The treadmill will
automatically rise to the maximum incline level and
then return to the minimum level. This will recalibrate
the incline system. When the incline system is
calibrated, remove the key from the console.
Reset
Tripped
c
MAINTENANCE AND TROUBLESHOOTING