ProForm 410 Treadmill Trainer English Manual - Page 8

the Left Upright 73. Insert an M10 x 96mm Bolt

Get ProForm 410 Treadmill Trainer PDF manuals and user guides View all ProForm 410 Treadmill Trainer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Hold a Bolt Spacer (79) inside the lower end of 5 the Right Upright (78). Insert an M10 x 96mm Bolt (5) with an M10 Star Washer (8) into the Right Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (79), M10 x 96mm Bolt (5), and M10 Star Washer (8). Orient the Right Upright (78) and the Right 78 Upright Spacer (80) as shown. Hold the Right Upright Spacer and the Right Upright against the Base (85). Be careful not to pinch the Upright Wire (77). Finger tighten the two M10 x 96mm Bolts (5); do not fully tighten the Bolts yet. 8 Rounded 77 80 Corner 85 Press a Base Endcap (82) into the Base (85). 79 82 5 6. Hold a Bolt Spacer (79) inside the lower end of the Left Upright (73). Insert an M10 x 96mm Bolt (5) with an M10 Star Washer (8) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (79), M10 x 96mm Bolt (5), and M10 Star Washer (8). Orient the Left Upright (73) and the Left Upright Spacer (83) as shown. Hold the Left Upright Spacer and the Left Upright against the Base (85). Finger tighten the two M10 x 96mm Bolt (5); do not fully tighten the Bolts yet. Press a Base Endcap (82) into the Base (85). 6 82 85 83 73 8 79 5 7. Set the Console (87) face down on a soft surface to avoid scratching the Console. Identify the 7 Right Handrail (90), which has a large hole in the 90 1 location shown. Hold the Right Handrail near the Console. Attach the console ground wire to the Right Handrail with an M4 x 13mm Screw (3). Next, insert the console wire into the large hole in the Right Handrail (90) and out of the top as 38 Console Ground Wire shown. Attach the Right Handrail with three M4 x 19mm Screws (1). Make sure that no wires are pinched. Start all three Screws before tight- 3 ening any of them; do not overtighten the Screws. Remove the ties from the Cage Nuts (38). Attach the Left Handrail (not shown) to the Console (87) in the same way. Note: There are no wires on the left side of the Console. 8 Console Wire 1 Large Hole 1 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
8
5.
Hold a Bolt Spacer (79) inside the lower end of
the Right Upright (78). Insert an M10 x 96mm
Bolt (5) with an M10 Star Washer (8) into the
Right Upright and the Bolt Spacer. Repeat this
step with a second Bolt Spacer (79), M10 x
96mm Bolt (5), and M10 Star Washer (8).
Orient the Right Upright (78) and the Right
Upright Spacer (80) as shown. Hold the Right
Upright Spacer and the Right Upright against the
Base (85).
Be careful not to pinch the Upright
Wire (77).
Finger tighten the two M10 x 96mm
Bolts (5);
do not fully tighten the Bolts yet.
Press a Base Endcap (82) into the Base (85).
77
80
78
79
82
8
6.
Hold a Bolt Spacer (79) inside the lower end of
the Left Upright (73). Insert an M10 x 96mm Bolt
(5) with an M10 Star Washer (8) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (79), M10 x 96mm
Bolt (5), and M10 Star Washer (8).
Orient the Left Upright (73) and the Left Upright
Spacer (83) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(85). Finger tighten the two M10 x 96mm Bolt
(5);
do not fully tighten the Bolts yet.
Press a Base Endcap (82) into the Base (85).
85
73
5
83
8
82
79
5
6
5
Rounded
Corner
85
7.
Set the Console (87) face down on a soft sur-
face to avoid scratching the Console. Identify the
Right Handrail (90), which has a large hole in the
location shown. Hold the Right Handrail near the
Console. Attach the console ground wire to the
Right Handrail with an M4 x 13mm Screw (3).
Next, insert the console wire into the large hole
in the Right Handrail (90) and out of the top as
shown. Attach the Right Handrail with three M4 x
19mm Screws (1).
Make sure that no wires are
pinched. Start all three Screws before tight-
ening any of them; do not overtighten the
Screws.
Remove the ties from the Cage Nuts (38).
Attach the Left Handrail (not shown) to the
Console (87) in the same way. Note: There are
no wires on the left side of the Console.
90
38
7
87
1
1
1
Large Hole
Console
Wire
3
Console
Ground Wire