ProForm 700tr Elliptical Uk Manual - Page 6

Wire Harnesses with the Button Screws.

Get ProForm 700tr Elliptical PDF manuals and user guides View all ProForm 700tr Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

2. Slide the Stabiliser Cover (31) onto the Frame (1). Next, move and lift each Flex Bar (14) out of the way 2 and slide the Stabiliser Cover onto the Front Stabiliser (3). Whilst another person lifts the front of the Frame, attach the Stabiliser Cover to the Front Stabiliser with two M4 x 52mm Screws (98). 31 1 14 3. With the help of a second person, carefully tip the 3 elliptical crosstrainer onto one side. Make sure that the Left and Right Stabiliser Endcaps (35, 92) are on the Rear Stabiliser (4). Attach the Rear Stabiliser (4) to the Frame (1) with four M8 x 45mm Button Screws (102) and four M8 Split Washers (94). With the help of a second person, carefully tip the elliptical crosstrainer back to the vertical position. 14 3 98 4 1 92 94 102 94 35 4. Have another person hold the Upright (2) in the position shown. Connect the Upper Wire Harness (86) to the Lower Wire Harness (87). Next, slide the Upright onto the Frame (1). Be careful to avoid disconnecting or pinching the Wire Harnesses. Attach the Upright with two M8 x 54mm Button Screws (33), two M8 x 38mm Button Screws (70), and four M8 Split Washers (94). Be careful to avoid damaging the Wire Harnesses with the Button Screws. Hold the Left and Right Handlebar Covers (26, 29) around the Upright (2) and the indicated tube. Press the Handlebar Covers together and connect them with an M4 x 16mm Round Head Screw (45). Hold the Left and Right Upright Covers (34, 38) around the Upright (2). Attach the Upright Covers with two M4 x 14mm Round Head Screws (93). 4 34 93 26 93 38 29 45 Tube 2 94 70 94 86 Make sure the wire harnesses do not get pinched and damaged during this step. 94 33 94 87 1 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
6
2. Slide the Stabiliser Cover (31) onto the Frame (1).
Next, move and lift each Flex Bar (14) out of the way
and slide the Stabiliser Cover onto the Front Stabiliser
(3). Whilst another person lifts the front of the Frame,
attach the Stabiliser Cover to the Front Stabiliser with
two M4 x 52mm Screws (98).
14
14
3
1
3
98
94
94
1
4
35
92
102
3. With the help of a second person, carefully tip the
elliptical crosstrainer onto one side.
Make sure that the Left and Right Stabiliser Endcaps
(35, 92) are on the Rear Stabiliser (4).
Attach the Rear Stabiliser (4) to the Frame (1) with
four M8 x 45mm Button Screws (102) and four M8
Split Washers (94).
With the help of a second person, carefully tip the
elliptical crosstrainer back to the vertical position.
2
31
4. Have another person hold the Upright (2) in the posi-
tion shown. Connect the Upper Wire Harness (86) to
the Lower Wire Harness (87). Next, slide the Upright
onto the Frame (1).
Be careful to avoid disconnect-
ing or pinching the Wire Harnesses.
Attach the
Upright with two M8 x 54mm Button Screws (33), two
M8 x 38mm Button Screws (70), and four M8 Split
Washers (94).
Be careful to avoid damaging the
Wire Harnesses with the Button Screws.
Hold the Left and Right Handlebar Covers (26, 29)
around the Upright (2) and the indicated tube. Press
the Handlebar Covers together and connect them with
an M4 x 16mm Round Head Screw (45).
Hold the Left and Right Upright Covers (34, 38)
around the Upright (2). Attach the Upright Covers with
two M4 x 14mm Round Head Screws (93).
26
93
93
34
38
86
2
Tube
1
87
94
70
33
94
94
94
29
45
4
Make sure the wire
harnesses do not
get pinched and
damaged
during this step.