ProForm Pro 1000 Instruction Manual - Page 10

not overtighten the #10 x 3/4 Screws 9.

Get ProForm Pro 1000 PDF manuals and user guides View all ProForm Pro 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

6. Attach a Handrail (86) to the Right Upright (90) with two 5/16" x 2 1/2" Screws (28) and two 5/16" Star Washers (11) in the location shown; do not fully tighten the Screws yet. Make sure not to pinch the Upright Wire (81), and make sure that the wire is on the indicated side of the Upright. Attach the other Handrail (86) to the Left Upright (89) in the same way. Note: There are no wires on the left side. Then, remove and discard the indicated screws (E). 6 11 E 28 86 28 89 11 E 86 90 81 7. IMPORTANT: To avoid damaging the Pulse Crossbar (93), do not use power tools and do not overtighten the #10 x 3/4" Screws (9). Orient the Pulse Crossbar (93) as shown. Attach the Pulse Crossbar to the Handrails (86) with four #10 x 3/4" Screws (9) and four #10 Star Washers (5); start all four Screws, and then tighten them. Next, firmly tighten the four 5/16" x 2 1/2" Screws (28). Then, remove the wire tie (A) from the Upright Wire (81). 7 9 28 5 86 93 9 5 86 81 28 A 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
10
6
81
90
89
86
E
86
28
11
11
28
6.
Attach a Handrail (86) to the Right Upright (90)
with two 5/16" x 2 1/2" Screws (28) and two
5/16" Star Washers (11) in the location shown;
do not fully tighten the Screws yet. Make sure
not to pinch the Upright Wire (81), and make
sure that the wire is on the indicated side of
the Upright.
Attach the other Handrail (86) to the Left
Upright (89) in the same way.
Note: There are
no wires on the left side.
Then, remove and discard the indicated
screws (E).
E
9
9
28
28
5
5
81
93
A
7
7.
IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do
not overtighten the #10 x 3/4" Screws (9).
Orient the Pulse Crossbar (93) as shown. Attach
the Pulse Crossbar to the Handrails (86) with
four #10 x 3/4" Screws (9) and four #10 Star
Washers (5);
start all four Screws, and then
tighten them.
Next, firmly tighten the four 5/16" x 2 1/2"
Screws (28).
Then, remove the wire tie (A) from the Upright
Wire (81).
86
86