Rane HAL1x Installation Guide - Page 108

HAL Rear Panel RAD Status, Possible Causes, Suggested Action, Power, Audio

Get Rane HAL1x PDF manuals and user guides View all Rane HAL1x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

HAL SYSTEM INSTALL GUIDE HAL Rear Panel RAD Status Possible Causes Suggested Action Power Comm Audio Tx Audio Rx The HAL is not powered. Power on the HAL and wait for it to boot up. A cable wired incorrectly is loading down the RAD power supply. Use a cable tester to verify the wiring of the shielded CAT 5e cable. The cable is plugged OFF OFF OFF OFF into something other than a RAD. If using a punch block, verify that the brown pair is properly punched. (Assuming T568B termination). The power supply on that RAD port is broken. Plugging the RAD cable into some other device (like an Ethernet switch) may load down the RAD power supply causing the error. Use a cable tester to verify The twisted pair in the the wiring of the shielded shielded CAT 5e cable CAT 5e cable. ON OFF OFF ON /OFF that carries communications data is If using a punch block, verify wired incorrectly or that the orange pair is prop- broken. erly punched (assuming T568B termination). Use a cable tester to verify the wiring of the shielded The RAD is not receiv- CAT 5e cable. ON ON OFF OFF ing an audio stream from If using a punch block, verify the HAL. that the green pair is properly punched (assuming T568B termination). Use a cable tester to verify the wiring of the shielded The HAL is not receiv- CAT 5e cable. ON ON ON OFF ing an audio stream from the RAD. If using a punch block, verify that the blue pair is properly punched (assuming T568B termination). 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
HAL Rear Panel RAD Status
Possible Causes
Suggested Action
Power
Comm
Audio
Tx
Audio
Rx
OFF
OFF
OFF
OFF
The HAL is not pow-
ered.
Power on the HAL and wait
for it to boot up.
A cable wired incor-
rectly is loading down
the RAD power supply.
Use a cable tester to verify
the wiring of the shielded
CAT 5e cable.
The cable is plugged
into something other
than a RAD.
If using a punch block, verify
that the brown pair is prop-
erly punched. (Assuming
T568B termination).
The power supply on
that RAD port is broken.
Plugging the RAD cable into
some other device (like an
Ethernet switch) may load
down the RAD power supply
causing the error.
ON
OFF
OFF
ON
/
OFF
The twisted pair in the
shielded CAT 5e cable
that carries com-
munications data is
wired incorrectly or
broken.
Use a cable tester to verify
the wiring of the shielded
CAT 5e cable.
If using a punch block, verify
that the orange pair is prop-
erly punched (assuming
T568B termination).
ON
ON
OFF
OFF
The RAD is not receiv-
ing an audio stream from
the HAL.
Use a cable tester to verify
the wiring of the shielded
CAT 5e cable.
If using a punch block, verify
that the green pair is properly
punched (assuming T568B
termination).
ON
ON
ON
OFF
The HAL is not receiv-
ing an audio stream from
the RAD.
Use a cable tester to verify
the wiring of the shielded
CAT 5e cable.
If using a punch block, verify
that the blue pair is properly
punched (assuming T568B
termination).
HAL SYSTEM INSTALL GUIDE
102