Rane HAL1x Installation Guide - Page 63

Toggle, Command, Digital Remote Port, Comm LED, Power LED, Switch Input/LED Output Ports

Get Rane HAL1x PDF manuals and user guides View all Rane HAL1x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

CHAPTER 2: Hardware Component Details The DR5 provides eight LED output ports that are coupled to the state of the corresponding DR5 switch input controls. You can connect an LED to each port to have a visual indicator of the DR5 operations. The operation of an LED Output port is governed by the Switch Input port configuration as follows: l Toggle: If the corresponding Switch Input port is configured as a toggle, the LED Output port follows the state of the Toggle control in the Control palette of the Processing Workspace. When the Toggle control is checked, the LED Output is high, turning the connected LED on. When the Toggle control is unchecked, the connected LED is off. l Command: When the corresponding Switch Input port is configured as a Command, the LED Output port follows the state of the Switch Input signal. When the switch is closed, the LED Output is high, turning the connected LED on. When the switch is open the connected LED is off. The following is a picture of the DR5 panel, along with descriptions of the hardware features. 1. Digital Remote Port Use this port to connect the DR5 to the HAL or EXP1 via a standard shielded CAT 5e cable. You must use a standard Ethernet cable for this connection. You can connect the DR5 to either a DR port or a RAD port. 2. Digital Remote LEDs Provides information about the health of the shielded CAT 5e connection between the DR5 and HAL or EXP1. The Comm LEDlights solidly if the DR's data communications pair is working properly. The Power LED lights solidly if HAL or EXP1 is supplying adequate power to the DR port. 3. Switch Input/LED Output Ports Provides a switch input (S), an LED output (L) and a ground connection (G) for each of the eight ports. The following is a wiring diagram for the DR5 panel. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
The DR5 provides eight LED output ports that are coupled to the state of the corresponding DR5 switch input con-
trols. You can connect an LED to each port to have a visual indicator of the DR5 operations. The operation of an
LED Output port is governed by the Switch Input port configuration as follows:
l
Toggle:
If the corresponding Switch Input port is configured as a toggle, the LED Output port follows the
state of the
Toggle
control in the Control palette of the Processing Workspace. When the Toggle control is
checked, the LED Output is high, turning the connected LED on. When the Toggle control is unchecked,
the connected LED is off.
l
Command:
When the corresponding Switch Input port is configured as a Command, the LED Output port
follows the state of the Switch Input signal. When the switch is closed, the LED Output is high, turning the
connected LED on. When the switch is open the connected LED is off.
The following is a picture of the DR5 panel, along with descriptions of the hardware features.
1.
Digital Remote Port
Use this port to connect the DR5 to the HAL or EXP1 via a standard shielded CAT 5e cable. You must
use a standard Ethernet cable for this connection. You can connect the DR5 to either a DR port or a RAD
port.
2.
Digital Remote LEDs
Provides information about the health of the shielded CAT 5e connection between the DR5 and HAL or
EXP1. The
Comm LED
lights solidly if the DR's data communications pair is working properly. The
Power LED
lights solidly if HAL or EXP1 is supplying adequate power to the DR port.
3.
Switch Input/LED Output Ports
Provides a switch input (S), an LED output (L) and a ground connection (G) for each of the eight ports.
The following is a wiring diagram for the DR5 panel.
CHAPTER 2: Hardware Component Details
57