Rane ZR1 CP64S Installation Manual - Page 13

Recommended Calibration Procedure The CP64S is a versatile instrument, allowing it to conform to lots of system applications. The result is complexity. For this reason, it is important be organized in system calibration. Once the internal switches are set and the system connected, take the time for proper calibration. This ordered list of system adjustments will make calibration easy and result in optimum performance. Most important: • Program Priority Assign rear panel off • Limiters rear panel +20 dBu • Duckers front panel OFF • Page Zone Levels front panel Min • Remote Controls front panel not selected • Paging Zone Assigns front panel 1&2 (both) PAGING ZONE ASSIGN LEVEL PAGE 1 PAGE 2 ZONE 1 ZONE 2 12 12 4 6 4 6 RMT 1&2 RMT 1&2 ACTIVE 0 10 0 10 ACTIVE PROGRAM INPUT LEVELS ZONE 1 ZONE 2 LINE 1 4 6 0 10 LINE 2 4 6 0 10 LINE 3 4 6 0 10 PRIORITY 4 6 DUCKER PROGRAM DEPTH SELECT L2 L3 L1 P RMT LEVEL 4 6 DUCKER PROGRAM DEPTH SELECT L2 L3 L1 P RMT LEVEL 4 6 OFF ON 0 10 OFF ON 10 SIG OL 10 SIG OL ZONE 1 ZONE 2 + 12 • 6 • 0 • 6 • 12 40 100 250 630 1.6k 4k 10k 40 100 250 630 1.6k 4k 10k CP64S COMMERCIAL PROCESSOR POWER CP64S COMMERCIAL AUDIO 100-240 V EQUIPMENT 24TJ 50/60 Hz 12 WATTS R Z2 PGM Z2 LEVEL REMOTES WIRING MIN MAX Vr Vc OUTPUTS Z2 EXPAND Z2 MONO ALL AUDIO AND REMOTES ARE CLASS 2 WIRING ZONE 2 ZONE 1 EXPAND OUT EXPAND OUT ZONE PAGE ZONE PAGE RANE CORP. MADE IN U.S.A. ACN 001 345 482 Z1 PGM D1 D0 Z1 LEVEL Vr Vc 2 PGM 1 PGM Z1 EXPAND Z1 RIGHT Z1 LEFT +- +- +- PROGRAM INPUTS LIMITER PRIORITY ZONE 1 ZONE 2 ASSIGN ZONE L L +8 +8 off 1 2 -20 +20 -20 +20 R R 1&2 PRIORITY 3 2 1 REMOTE PAGE REMOTE 1 INPUT 1 ZONE ASSIGN WIRING Z1 Z2 PAGING INPUTS PAGE 2 TRIM PAGE 1 TRIM PAGE 2 PAGE 1 DETECT THRESHOLD REMOTE 2 INPUT 2 Z2 Z1 +- +30 +60 OL +30 +60 MIC LINE MIC LINE Make sure the power is disconnected! Control Presets: Page settings (repeat for second page input): • Input Pad rear panel • Input gain trim rear panel • Detect Threshold rear panel • Paging Zone Assign front panel • Paging Level, Zone 1 front panel • Paging Level, Zone 2 front panel • Phantom Power internal • Pre/Post summing internal • Page Priority internal MIC or LINE as required Center (12:00) Min (CCW, active) 1&2 (both) Min Min As required. Default Off As required. Default Post-VCA As required. Default Page 1 Program Input settings: • Priority Assign Zone • Program Input Levels • Priority Threshold • Priority Release Time rear panel front panel internal internal off Min Set to -50 at factory (internal adjust -∞ to -35 dBu) Set to 12 sec. at factory (internal adjust 2 to 20 sec.) Zone Settings (repeat for second zone): • Expand Out rear panel • Limiter Threshold rear panel • Zone Level front panel • Program Select front panel • Ducker front panel • Ducker Depth front panel • RMT (Remote) front panel • EQ front panel • Stereo / Mono switch internal As required (Zone/Program/Page) CW, +20 dBu Max L1 (if your input is on L1). OFF Center (about 15 dB) Out Flat (center detent position) As required (Zone 1 only. Default: Stereo) System Connections: • Connect page mics or line-level paging source • Connect Program sources • Connect Outputs to amplifiers • Connect Remotes You are now ready to calibrate the CP64S... 13