Ricoh 002052MIU User Guide - Page 143

FUSING, 6.5 LSU, Error Type

Get Ricoh 002052MIU - AC 204 B/W Laser PDF manuals and user guides
UPC - 026649118692
View all Ricoh 002052MIU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 143 highlights

ENGINE F/W 6.6.4 FUSING The resistance of the thermistor varies inversely with the temperature of the hot roller. The control circuit monitors the temperature through the thermistor and turns the fusing lamp on and off. This keeps the hot roller at the operating temperature. Error Type Error Description Open heat error Lower heat error Goes lower than 68°C for 28 seconds at the time of warm up • Standby: Goes lower than 80°C over 10 seconds • Print mode: 1. Goes lower than 145°C for 4 seconds for consecutive pages. 2. Sets at 25°C or lower than the fixed fusing temperature over 4 seconds for consecutive pages. Over heat error Goes higher than 220°C for 3 seconds 6.6.5 LSU The LSU consists of the LD (Laser Diode) and the polygon motor. The LD turns and drives the polygon motor when it gets a print signal. Hsync occurs when the light part gets the beam. LReady occurs when the polygon motor speed gets to a correct condition. The LSU controller gets to 1 when the LSU is ready. If not, an error is shown. Error Type Error Description Polygon motor error When the polygon motor's speed is not correct Hsync error The polygon motor's speed is correct, but the Hsync signal is not shown. Detailed Descriptions SM 6-13 B173

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
ENGINE F/W
SM
6-13
B173
Detailed
Descriptions
6.6.4 FUSING
The resistance of the thermistor varies inversely with the temperature of the hot
roller. The control circuit monitors the temperature through the thermistor and turns
the fusing lamp on and off. This keeps the hot roller at the operating temperature.
Error Type
Error
Description
Open heat error
Goes lower than 68°C for 28 seconds at the time of warm up
Lower heat error
•
Standby:
Goes lower than 80°C over 10 seconds
•
Print mode:
1. Goes lower than 145°C for 4 seconds for consecutive
pages.
2. Sets at 25°C or lower than the fixed fusing temperature
over 4 seconds for consecutive pages.
Over heat error
Goes higher than 220°C for 3 seconds
6.6.5 LSU
The LSU consists of the LD (Laser Diode) and the polygon motor. The LD turns
and drives the polygon motor when it gets a print signal. Hsync occurs when the
light part gets the beam. LReady occurs when the polygon motor speed gets to a
correct condition. The LSU controller gets to 1 when the LSU is ready. If not, an
error is shown.
Error Type
Error
Description
Polygon motor error
When the polygon motor’s speed is not correct
Hsync error
The polygon motor’s speed is correct, but the Hsync signal is not
shown.