Ricoh AP610N Maintenance Manual - Page 14

OHP transparencies, Envelopes - drivers

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Paper and Other Media OHP transparencies Printer setup 1 Press [Paper Input] menu, [Paper Type], and then [Transparency] on the control panel. Note ❒ The paper type selected using the printer driver overrides that selected using the control panel. Printer driver setup Click [Transparency] in the [Type:] list. Enabled paper feeding tray Bypass tray Number of sheets that can Load only one OHP transparency at the same time onto the bypass be set tray. Both-sided printing Not possible Additional cautions • Print speed for OHP transparencies is slower than for plain paper. • Due to switching modes, the machine will be on standby for thirty or forty seconds after the job was received. Envelopes Printer setup Press [Paper Input] menu, [Paper Type], and then press [Thick Paper] on the control panel. Note ❒ The paper type selected using the printer driver overrides that selected using the control panel. Printer driver setup Click [Thick] in the [Type:] list. Enabled paper feeding tray Any input tray can be used. Both-sided printing Additional cautions 10 Note ❒ Make sure paper is not stacked higher than the upper limit mark (T) inside the tray. Make sure paper is not stacked higher than the paper guides inside the bypass tray. Not possible • Check the print side is facing up. • Check there is no air in the envelopes before loading. • For better print quality, we recommend the right, left, top, and bottom print margins to be at least 20 mm (0.8") each. • Load only one size and type of envelope at a time. • Before loading envelopes, flatten their leading edges (the edge going into the printer) by running a pencil or ruler across them. • Some kinds of envelope might cause misfeeds, wrinkles or print poorly. • Print quality on envelopes may be uneven if parts of an envelope have differing thicknesses. Print one or two envelopes to check print quality.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Paper and Other Media
10
1
OHP transparencies
Envelopes
Printer setup
Press
[
Paper Input
]
menu,
[
Paper Type
]
, and then
[
Transparency
]
on
the control panel.
Note
❒
The paper type selected using the printer driver overrides that
selected using the control panel.
Printer driver setup
Click
[
Transparency
]
in the
[
Type:
]
list.
Enabled paper feeding tray
Bypass tray
Number of sheets that can
be set
Load only one OHP transparency at the same time onto the bypass
tray.
Both-sided printing
Not possible
Additional cautions
•
Print speed for OHP transparencies is slower than for plain pa-
per.
•
Due to switching modes, the machine will be on standby for
thirty or forty seconds after the job was received.
Printer setup
Press
[
Paper Input
]
menu,
[
Paper Type
]
, and then press
[
Thick Paper
]
on the control panel.
Note
❒
The paper type selected using the printer driver overrides that
selected using the control panel.
Printer driver setup
Click
[
Thick
]
in the
[
Type:
]
list.
Enabled paper feeding tray
Any input tray can be used.
Note
❒
Make sure paper is not stacked higher than the upper limit
mark (
T
) inside the tray. Make sure paper is not stacked higher
than the paper guides inside the bypass tray.
Both-sided printing
Not possible
Additional cautions
•
Check the print side is facing up.
•
Check there is no air in the envelopes before loading.
•
For better print quality, we recommend the right, left, top, and
bottom print margins to be at least 20 mm (0.8”) each.
•
Load only one size and type of envelope at a time.
•
Before loading envelopes, flatten their leading edges (the edge
going into the printer) by running a pencil or ruler across
them.
•
Some kinds of envelope might cause misfeeds, wrinkles or
print poorly.
•
Print quality on envelopes may be uneven if parts of an enve-
lope have differing thicknesses. Print one or two envelopes to
check print quality.