Rocketfish RF-RBREC User Manual (English) - Page 18

Listening to music, To establish communications, To listen to music - rocketboost wireless receiver

Page 18 highlights

To establish communications: 1 If possible, bring your Rocketboost hub device and the new Rocketboost receiver into the same room. 2 Press the Power button on the Rocketboost hub device to turn it on. 3 Press the Power button on your Rocketboost receiver to turn it on. 4 Press and hold the on the Rocketboost hub device for more than three seconds to put it into joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode for 30 seconds. 5 Press and hold the on your Rocketboost receiver for more than three seconds to put it into joining mode. • When successfully joined, the power indicator LEDs on both products will stop blinking and stay on. • If joining fails after 30 seconds, the power indicator LEDs will begin flashing at a slower rate. If this occurs, repeat the above steps. • Repeat steps 1-5 for each additional Rocketboost device you are adding to your network. Power on indicator Note: Rocketboost devices have their own memory. After the devices are joined once, they will remember each other and join automatically when they are powered on again. Because of this, you can join all of your network components in the same room before installing them in their permanent locations throughout the house. Listening to music To listen to music: 1 Turn on the wireless sender and wireless receiver. The power indicator LEDs should light steadily. If they are blinking you need to rejoin the sender and receiver. See "Establishing communication" on page 17. 2 Play music from the audio device connected to your sender and listen to it from speakers attached to the wireless receiver. 3 Adjust the volume level on your wireless receiver. If you have multiple audio sources in your Rocketboost network, press the SOURCE button on the wireless receiver to hear the next audio source. Press the SOURCE button again to cycle through all available audio sources. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31

18
To establish communications:
1
If possible, bring your Rocketboost hub device and the new Rocketboost
receiver into the same room.
2
Press the Power button on the Rocketboost hub device to turn it on.
3
Press the Power button on your Rocketboost receiver to turn it on.
4
Press and hold the
on the Rocketboost hub device for more than three
seconds to put it into joining mode. The power indicator starts blinking
rapidly and the unit will stay in joining mode for 30 seconds.
5
Press and hold the
on your Rocketboost receiver for more than three
seconds to put it into joining mode.
When successfully joined, the power indicator LEDs on both products
will stop blinking and stay on.
If joining fails after 30 seconds, the power indicator LEDs will begin
flashing at a slower rate. If this occurs, repeat the above steps.
Repeat steps 1-5 for each additional Rocketboost device you are
adding to your network.
Note
: Rocketboost devices have their own memory. After the devices are joined once,
they will remember each other and join automatically when they are powered on
again. Because of this, you can join all of your network components in the same
room before installing them in their permanent locations throughout the house.
Listening to music
To listen to music:
1
Turn on the wireless sender and wireless receiver. The power indicator
LEDs should light steadily. If they are blinking you need to rejoin the
sender and receiver. See “Establishing communication” on page 17.
2
Play music from the audio device connected to your sender and listen to
it from speakers attached to the wireless receiver.
3
Adjust the volume level on your wireless receiver. If you have multiple
audio sources in your Rocketboost network, press the
SOURCE
button on
the wireless receiver to hear the next audio source. Press the
SOURCE
button again to cycle through all available audio sources.
Power on
indicator