Samsung DVD 1080P7 User Manual (ENGLISH) - Page 17

Connecting to a TV (Video) - user manual

Page 17 highlights

Connections CONNECTIONS Connecting to a TV (Video) 1 Using Video/Audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT jacks on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN jacks of your TV. 2 Turn on your DVD player and TV. 3 Set the Video Output to S-VIDEO in the Display Setup menu. (See pages 52 to 54). You can also use the VIDEO SEL. button to change the Video Output mode. (See page 12) 4 Press the input selector button on your TV remote control until the Video signal from the DVD player appears on the TV screen. RED RED WHITE YELLOW Audio Cable Video Cable (Included) (Included) WHITE YELLOW Note - Noise may be generated if the audio cable placed too close to the power cable. - If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 18 to 19) - The number and position of the jacks may vary depending on your TV set. Please refer to the user's manual of your TV. - If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) jack of the DVD player. - If you press the VIDEO SEL. button when the DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (COMPOSITE/S-Video ➝ I-SCAN ➝ P-SCAN). When HDMI is connected, these output modes will not appear. - When using an HDMI connection, S-Video will not be output. ENG-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65

ENG-
17
Connections
C
ONNECTIONS
1
Using V
ideo/Audio cables, connect the
VIDEO
(yellow)/AUDIO
(red and white) OUT
jacks on the rear of the DVD player to the
VIDEO (yellow)/AUDIO (red and white) IN
jacks of your
TV.
2
T
urn on your DVD player and TV.
Note
-
Noise may be generated if the audio cable placed too close to the power cable.
-
If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 18 to 19)
-
The number and position of the jacks may vary depending on your TV set. Please refer to the user's manual
of your TV.
-
If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) jack of the DVD
player.
-
If you press the VIDEO SEL. button when the DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (COMPOSITE/S-Video
I-SCAN
P-SCAN).
When HDMI is connected, these output modes will not appear.
-
When using an HDMI connection, S-Video will not be output.
RED
WHITE
YELLOW
RED
WHITE
YELLOW
Audio Cable
(Included)
Video Cable
(Included)
3
Set the V
ideo Output to
S-VIDEO
in the Display Setup menu.
(See pages 52 to 54).
You can also use the
VIDEO SEL.
button to change the V
ideo
Output mode. (See page 12)
4
Press the input selector button on your
TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Connecting to a TV (V
ideo)