Samsung ML-1865W User Manual (user Manual) (ver.1.01) (English) - Page 27

Wireless network name and network key Wireless networks require higher security, so when an access point is first set up, a network name (SSID), the type of security used, and a Network Key are created for the network. Locate this information before proceeding with the machine installation. Printing network configuration report In ready mode, press and hold the (WPS button) for about 15 seconds. You can find your machine's MAC address and IP address. For example: • MAC Address: 00:15:99:41:A2:78 • IP Address: 192.0.0.192 • WPS PIN NUMBER : 75135772 Choosing the wireless network installation type There are various ways to install the wireless network to connect to the machine. You can install a wireless network from the machine's control panel or the computer. For most users, we recommend using the WPS ( ) button to configure the wireless network settings. From the control panel • WPS ( ) : If your machine and an access point (or wireless router) support Wi-Fi Protected Setup™(WPS), you can easily configure the wireless network settings by pressing the WPS ( ) button on the control panel. (See "Setting a wireless network with the WPS button" on page 27). From the computer From the compurter, we recommend using a USB cable with the program provided in the supplied software CD. • With a USB cable: You can simply set up a wireless network using the program on the supplied software CD. Only Windows and Macintosh operating system are supported (See "Setting a wireless network with USB cable" on page 28). You can also install a wireless network in Printer Settings Utility with a USB cable after installing the driver (Windows and Macintosh operating systems are supported). Setting a wireless network with the WPS button You can install a wireless network with the WPS ( ) button. • After compleleting the wireless network connection, you need to install a machine driver to print from an application. • See your network administrator, or the person that set up your wireless network, for information about your network configuration. Setting a wireless network with the WPS button If your machine and an access point (or wireless router) support Wi-Fi Protected Setup™(WPS), you can easily configure the wireless network settings by pressing the WPS ( ) button on the control panel. Items to prepare You need to ensure you have the following items ready to use: • Check if the access point (or wireless router) supports Wi-Fi Protected Setup™ (WPS). • Check if your machine supports Wi-Fi Protected Setup™ (WPS). • Networked computer (PIN mode only) Choosing your network connection There are two methods to connect your machine to a wireless network using the WPS ( ) button on the control panel. The Push Button Configuration (PBC) method allows you to connect your machine to a wireless network by pressing both the WPS ( ) button on the control panel of your machine and the WPS (PBC) button on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router) respectively. The Personal Identification Number (PIN) method helps you connect your machine to a wireless network by entering the supplied PIN information on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router). Factory default in your machine is PBC mode, which is recommended for a typical wireless network environment. Connecting to a wireless network in PBC mode To connect your machine to the wireless network in PBC mode, follow the following steps: You need to check the status of the wireless LED. 1. Press and hold the WPS ( ) button on the control panel for about 2 - 4 seconds until the status LED blinks quickly. • : The light blinks slowly on wireless LED. The machine starts connecting to the wireless network. The LED blinks slowly for up to two minutes until you press the PBC button on access point (or wireless router). 2. : Press the WPS (PBC) button on the access point (or wireless router). The wireless LED blinks in the order below: a) : The light blinks fast on the wireless LED. The machine is connecting to the access point (or wireless router). b) : When the machine is successfully connected to the wireless network, the wireless LED light stays on. Connecting to the wireless network in PIN mode To connect your machine to the wireless network, follow the following steps: You need to check the status of the wireless LED. 1. Print the network configuration report including PIN number must be printed. In ready mode, press and hold the WPS ( ) button on the control panel for about 15 seconds. You can find you machine's PIN number. 2. Press and hold the WPS ( ) button on the control panel for more than 4 seconds until the status LED on. • : The light blinks slowly on the wireless LED. The machine starts connecting to access point (or wireless router). 3. You need to enter eight-digit PIN number within two minutes to the computer which is connected to the access point (or wireless router). Wireless network setup_ 27