Samsung NX60A6711SS/AA Installation Guide - Page 23

START/SET, Valve Stem

Get Samsung NX60A6711SS/AA PDF manuals and user guides View all Samsung NX60A6711SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

To check and adjust the oven burner air adjustment shutters: 1. Open the oven door. 2. Remove the oven racks. 3. Remove the oven floor. 4. Press the Bake pad, then the START/SET pad. 5. After the oven has lit, visually check the flames coming out of the upper and lower burners. If adjustment is needed, carefully adjust the air adjustment shutters. The shutters are located at the base of the burner manifolds near the back oven wall. Locking screw To adjust the shutter, loosen the locking screw and rotate the shutter towards the open or closed position as needed. If flames are lifting off the burner ports, gradually reduce the air shutter opening until the flames are stabilized. If flames are too yellow and/or too large, gradually increase the air shutter opening until the flames have approximately a 1-in blue cone. NOTE If the range is set up for natural gas, the flames should burn with no yellow tipping. If the range is set up for LP gas, small yellow tips at the end of the cones are normal. After the flames are adjusted properly, shut off the oven, retighten the locking screws, replace the oven bottom and racks, and close the oven door. To adjust flame low setting Identify which burner is exhibiting too high or too low of simmer rate via manifold panel graphics. 1. Rotate a knob to LO position and remove the knob from the valve stem while the flame is lit. Simmer Set Screw Valve Stem Small Screwdriver 2. Carefully push the screw driver into the stem of the valve, until it hits the simmer set screw. Make sure the screwdriver flathead is seated into the set screw groove. 3. Rotate valve set screw clockwise to decrease LO setting flame output, or rotate set screw counter clockwise to increase LO setting flame output. WARNING 1. Do not completely remove the valve set screw from the valve stem. The valve set screw is an integral part of the gas valve assembly. Removing the valve set screw will cause gas to leak. 2. After adjusting the valve set screw, inspect the assembly for gas leaks. Locking screw Installation instructions Install_NX60A6_DG68-01337A-00_EN+MES+CFR.indb 23 English 23 2020-12-30 10:56:14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English 23
Installation instructions
To check and adjust the oven burner air adjustment shutters:
1.
Open the oven door.
2.
Remove the oven racks.
3.
Remove the oven floor.
4.
Press the
Bake
pad, then the
START/SET
pad.
5.
After the oven has lit, visually check the flames coming out of the upper and
lower burners. If adjustment is needed, carefully adjust the air adjustment
shutters.
Locking screw
The shutters are located at the base of the
burner manifolds near the back oven wall.
To adjust the shutter, loosen the locking
screw and rotate the shutter towards the
open or closed position as needed. If flames
are lifting off the burner ports, gradually
reduce the air shutter opening until the
flames are stabilized.
If flames are too yellow and/or too large,
gradually increase the air shutter opening
until the flames have approximately a 1-in
blue cone.
NOTE
If the range is set up for natural gas, the flames should burn with no yellow
tipping. If the range is set up for LP gas, small yellow tips at the end of the cones
are normal.
Locking screw
After the flames are adjusted properly, shut
off the oven, retighten the locking screws,
replace the oven bottom and racks, and
close the oven door.
To adjust flame low setting
Identify which burner is exhibiting too high or too low of simmer rate via manifold
panel graphics.
Simmer Set
Screw
1.
Rotate a knob to
LO
position and remove
the knob from the valve stem while the
flame is lit.
Small
Screwdriver
Valve Stem
2.
Carefully push the screw driver into the
stem of the valve, until it hits the simmer
set screw. Make sure the screwdriver
flathead is seated into the set screw
groove.
3.
Rotate valve set screw clockwise to
decrease
LO
setting flame output, or
rotate set screw counter clockwise to
increase
LO
setting flame output.
WARNING
1.
Do not completely remove the valve set screw from the valve stem. The valve
set screw is an integral part of the gas valve assembly. Removing the valve set
screw will cause gas to leak.
2.
After adjusting the valve set screw, inspect the assembly for gas leaks.
Install_NX60A6_DG68-01337A-00_EN+MES+CFR.indb
23
Install_NX60A6_DG68-01337A-00_EN+MES+CFR.indb
23
2020-12-30
°° 10:56:14
2020-12-30
°° 10:56:14