Samsung NX60T8711SS/AA Installation Guide - Page 25

Valve Stem, Simmer Set

Get Samsung NX60T8711SS/AA PDF manuals and user guides View all Samsung NX60T8711SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Memo To adjust flame low setting Identify which burner is exhibiting too high or too low of simmer rate via manifold panel graphics. 1. Rotate a knob to LO position and remove the knob from the valve stem while the flame is lit. Simmer Set Screw Valve Stem Small Screwdriver 2. Carefully push the screw driver into the stem of the valve, until it hits the simmer set screw. Make sure the screwdriver flathead is seated into the set screw groove. 3. Rotate valve set screw clockwise to decrease LO setting flame output, or rotate set screw counter clockwise to increase LO setting flame output. WARNING 1. Do not completely remove the valve set screw from the valve stem. The valve set screw is an integral part of the gas valve assembly. Removing the valve set screw will cause gas to leak. 2. After adjusting the valve set screw, inspect the assembly for gas leaks. Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 25 English 25 2020-03-26 6:41:26 Installation instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English 25
Installation instructions
To adjust flame low setting
Identify which burner is exhibiting too high or too low of simmer rate via manifold
panel graphics.
Simmer Set
Screw
1.
Rotate a knob to
LO
position and remove
the knob from the valve stem while the
flame is lit.
Small
Screwdriver
Valve Stem
2.
Carefully push the screw driver into the
stem of the valve, until it hits the simmer
set screw. Make sure the screwdriver
flathead is seated into the set screw
groove.
3.
Rotate valve set screw clockwise to
decrease
LO
setting flame output, or
rotate set screw counter clockwise to
increase
LO
setting flame output.
WARNING
1.
Do not completely remove the valve set screw from the valve stem. The valve
set screw is an integral part of the gas valve assembly. Removing the valve set
screw will cause gas to leak.
2.
After adjusting the valve set screw, inspect the assembly for gas leaks.
Memo
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd
25
2020-03-26
°° 6:41:26