Samsung WF405ATPASU/AA User Manual Ver.1.0 (English, French, Spanish) - Page 17

Important Note To Installer

Get Samsung WF405ATPASU/AA PDF manuals and user guides View all Samsung WF405ATPASU/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

01 Installing your washer IMPORTANT NOTE TO INSTALLER Please read the following instructions carefully before installing the washer. These instructions should be retained for future reference. We recommend you hire a professional to install this washer. STEP 1 Removing the Shipping Bolts Before using your washer, you must remove the four shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Cover the holes with the supplied Bolt Hole Covers (See page 19). 4. Keep the shipping bolts and spacers for future use. STEP 2 Selecting a Location Before you install your washer, make sure the location: • Has a hard, level surface • Is away from direct sunlight • Has adequate ventilation • Will not freeze (tempuratures are never below 32 °F or 0 °C). • Is away from heat sources such as oil or gas • Has enough room for the power cord. • Doesn't have any carpeting that will obstruct ventilation openings. STEP 3 Installing your Washer 1. If you use a stand pipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high. You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive length. For situations where the drain hose cannot 96" Max 18" Min be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. Laundry tub Stand pipe Hose retainer Tie strap 96" Max 18" Min Do not insert the drain hose too far into the stand pipe: 6 - 8 inches, and no more. Cold 2. Check the inlet hose to ensure a washer is inside each fill hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each fill hose to the water valve. Make sure the hose with Hot printed on it is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. Hot Rubber Washer For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. Installing your washer _17 WF405ATPA-03145A-02_EN.indd Sec2:17 2012-03-12 3:07:18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Installing your washer
_17
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing the washer.
These instructions should be retained for future reference.
We recommend you hire a professional to install this washer.
STEP 1
Removing the Shipping Bolts
Before using your washer, you must remove the four shipping bolts
from the back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with the spacer
through the hole in the rear wall of your washer. Repeat for each
bolt.
3.
Cover the holes with the supplied Bolt Hole Covers (See page 19).
4.
Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your washer, make sure the location:
•
Has a hard, level surface
•
Is away from direct sunlight
•
Has adequate ventilation
•
Will not freeze (tempuratures are never below 32 °F or 0 °C).
•
Is away from heat sources such as oil or gas
•
Has enough room for the power cord.
•
Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 3
Installing your Washer
1.
If you use a stand pipe, make sure the connection
between the drain hose and the standpipe is NOT
airtight. The standpipe must be at least 18 in or 46
cm high.
You must always exercise caution to avoid
collapsing or damaging the drain hose. For best
results, the drain hose should not be restricted
in any way – by elbows, couplings, or excessive
length. For situations where the drain hose cannot
be conveniently elevated to at least 18 in or 46 cm,
the drain hose must be supported.
Do not insert the drain hose too far into the stand
pipe: 6 - 8 inches, and no more.
2.
Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet connections.
On the other end of the hose, check for one rubber washer per hose
and attach each fill hose to the water valve. Make sure the hose with
Hot printed on it is attached to the HOT faucet. Tighten by hand until
snug, then two-thirds of a turn with pliers.
For correct water use, connect both HOT and COLD water valves. If
either or both are not connected, an “nF” (no fill) error can occur.
01 Installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Stand pipe
Cold
Hot
Rubber
Washer
WF405ATPA-03145A-02_EN.indd Sec2:17
WF405ATPA-03145A-02_EN.indd
Sec2:17
2012-03-12
3:07:18
2012-03-12
3:07:18