Sanyo PLC-WXU10N Owners Manual - Page 35

Order Replacement Lamp, En-34 - plc wxu10

Get Sanyo PLC-WXU10N - WXGA LCD Projector PDF manuals and user guides
UPC - 086483069420
View all Sanyo PLC-WXU10N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

1. Turn off the projector and unplug the AC power cord. 2. Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can access the lamp cover. 3. Loosen the access panel screw and open the panel. 4. Loosen the screws on the bottom of the lamp assembly. 5. Grasp the lamp handle and pull the lamp assembly directly out of the projector. 6. Replace with the new lamp. 7. Tighten the screws on the bottom of lamp assembly. 8. Tighten the screw on the lamp cover. 9. Reset the lamp hour. Refer to the "Setting (Computer/Video Mode)" menu. Dispose of the used lamp according to local regulations. Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. Since the lamp is made of glass, do not drop the unit and do not scratch the glass. Do not reuse the old lamp. This could cause the lamp to explode. Be sure to turn off the projector and unplug the AC power cord before replacing the lamp. Do not use the projector with the lamp cover removed. ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp,give the following information to the dealer. Model No. of your projector: Replacement Lamp Type No.: PLC-WXU10N/ WXU10E/ WXU10B POA-LMP113 (Service Parts No. 610 336 0362) EN-34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
EN-34
1.
Turn off the projector and unplug the AC power
cord.
2.
Place a protective sheet (cloth) beneath the
projector. Turn the projector over so you can
access the lamp cover.
3.
Loosen the access panel screw and open the
panel.
4.
Loosen the screws on the bottom of the lamp
assembly.
5.
Grasp the lamp handle and pull the lamp
assembly directly out of the projector.
6.
Replace with the new lamp.
7.
Tighten the screws on the bottom of lamp
assembly.
8.
Tighten the screw on the lamp cover.
9.
Reset the lamp hour. Refer to the “Setting
(Computer/Video Mode)” menu.
J
Dispose of the used lamp according to local regulations.
J
Ensure that screws are tightened properly. Screws not tightened fully may result
in injury or accidents.
J
Since the lamp is made of glass, do not drop the unit and do not scratch the
glass.
J
Do not reuse the old lamp. This could cause the lamp to explode.
J
Be sure to turn off the projector and unplug the AC power cord before replacing
the lamp.
J
Do not use the projector with the lamp cover removed.
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.
When ordering a projection
lamp,give the following information to the dealer.
Q
Model No. of your projector:
PLC-WXU10N/ WXU10E/ WXU10B
Q
Replacement Lamp Type No.:
POA-LMP113
(Service Parts No. 610 336 0362)