Home » Seagate Manuals » Hard Drives » Seagate ST3300655LC » Manual Viewer

Seagate ST3300655LC Cheetah 15K.5 SCSI Product Manual - Page 61

SCSI bus conditions and miscellaneous features supported

View all Seagate ST3300655LC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

10.4 SCSI bus conditions and miscellaneous features supported Asynchronous SCSI bus conditions supported by the drive are listed below. These conditions cause the SCSI device to perform certain actions and can alter the SCSI bus phase sequence. Other miscellaneous operating features supported are also listed here. Refer to the Parallel SCSI Interface Manual and the SCSI Commands Reference Manual for details. Table 13: SCSI bus conditions and other miscellaneous features Condition/feature supported by: Supported Y Y Y N Y N Y Y Y N Y Y Y Y Y Y Y N Conditions or feature Adaptive Caching Arbitrating System Asynchronous Data Transfer Asynchronous Event Notification Attention Condition Auto Contingent Allegiance Condition Contingent Allegiance Condition Deferred Error Handling Disconnect/Reconnect High voltage differential (HVD) interface available Low voltage differential (LVD) interface available Parameter Rounding (controlled by the Round bit in Mode Select page 0) Queue tagging (up to 64 Queue tags supported) Reporting actual retry count in Extended Sense bytes 15, 16 and 17. Reset Condition Segmented Caching Synchronous Data Transfer Zero Latency Read Supported Y Y Y Y Y Y Y Y N Status Good Check Condition Condition Met/Good Busy Intermediate/Good Intermediate/Condition Met/Good Reservation Conflict Queue Full ACA Active Cheetah 15K.5 SCSI Product Manual, Rev. J 55

Section	Page
1.0 Seagate Technology support services	7
2.0 Scope	8
3.0 Applicable standards and reference documentation	9
3.1 Standards	9
3.1.1 Electromagnetic compatibility	9
3.1.2 Electromagnetic susceptibility	9
3.2 Electromagnetic compliance	10
3.3 European Union Restriction of Hazardous Substances (RoHS)	10
3.4 Reference documents	11
4.0 General description	12
4.1 Standard features	13
4.2 Media characteristics	13
4.3 Performance	14
4.4 Reliability	14
4.5 Formatted capacities	14
4.5.1 Programmable drive capacity	15
4.6 Factory installed accessories	15
4.7 Options (factory installed)	15
4.8 Accessories	15
5.0 Performance characteristics	16
5.1 Internal drive characteristics (transparent to user)	16
5.2 SCSI performance characteristics (visible to user)	16
5.2.1 Seek time	17
5.2.2 Format command execution time (minutes) [1]	17
5.2.3 Generalized performance characteristics	17
5.3 Start/stop time	18
5.4 Prefetch/multi-segmented cache control	18
5.5 Cache operation	18
5.5.1 Caching write data	19
5.5.2 Prefetch operation	19
6.0 Reliability specifications	20
6.1 Error rates	20
6.1.1 Recoverable Errors	20
6.1.2 Unrecoverable Error	20
6.1.3 Seek errors	21
6.2 Reliability and service	21
6.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	21
6.2.2 Preventive maintenance	21
6.2.3 Hot plugging Cheetah 15K.5 SCSI disc drives	22
6.2.4 S.M.A.R.T.	22
6.2.5 Thermal monitor	24
6.2.6 Drive Self Test (DST)	24
6.2.6.1 DST Failure Definition	25
6.2.6.2 Implementation	25
6.2.7 Product warranty	26
7.0 Physical/electrical specifications	28
7.1 AC power requirements	28
7.2 DC power requirements	28
7.2.1 Conducted noise immunity	30
7.2.2 Power sequencing	30
7.2.3 Current profile	30
7.3 Power dissipation	32
7.4 Environmental limits	35
7.4.1 Temperature	35
7.4.2 Relative humidity	35
7.4.3 Effective altitude (sea level)	35
7.4.4 Shock and vibration	36
7.4.4.1 Shock	36
7.4.4.2 Vibration	38
7.4.5 Air cleanliness	38
7.4.6 Corrosive environment	38
7.4.7 Acoustics	39
7.4.8 Electromagnetic susceptibility	39
7.5 Mechanical specifications	39
8.0 Defect and error management	41
8.1 Drive internal defects	41
8.2 Drive error recovery procedures	41
8.3 SCSI systems errors	43
8.4 Background Media Scan	43
8.5 Media Pre-Scan	43
8.6 Deferred Auto-Reallocation	44
8.7 Idle Read After Write	44
9.0 Installation	45
9.1 Drive ID/option select header	45
9.1.1 Notes for Figures 10 and 11.	47
9.1.2 Function description	48
9.2 Drive orientation	49
9.3 Cooling	49
9.4 Drive mounting	50
9.5 Grounding	50
10.0 Interface requirements	51
10.1 General description	51
10.2 SCSI interface messages supported	51
10.3 SCSI interface commands supported	52
10.3.1 Inquiry Vital Product data	56
10.3.2 Mode Sense data	57
10.4 SCSI bus conditions and miscellaneous features supported	61
10.5 Synchronous data transfer	62
10.5.1 Synchronous data transfer periods supported	62
10.5.2 REQ/ACK offset	62
10.6 Physical interface	62
10.6.1 DC cable and connector	63
10.6.2 SCSI interface physical description	64
10.6.3 SCSI interface cable requirements	65
10.6.3.1 Cable requirements	65
10.6.4 Mating connectors	65
10.6.4.1 Mating connectors for LW model drives	66
10.6.4.2 Mating connectors for LC model drives	66
10.7 Electrical description	74
10.7.1 Multimode—SE and LVD alternatives	74
10.7.1.1 General cable characteristics	75
10.7.1.2 Single-ended drivers/receivers	75
10.7.1.3 Cables for low voltage differential drivers/receivers	76
10.8 Terminator requirements	77
10.9 Terminator power	77
10.10 Disc drive SCSI timing	78
10.11 Drive activity LED	80