Seagate ST336807FC Cheetah 10K.7 FC Product Manual - Page 82

Pins 9, 10, 17, 18, and 39 are option select pins and are tied high by the drive circuitry.

Page 82 highlights

9.5.4 Pin descriptions This section provides a pin-out of the FC-SCA and a description of the functions provided by the pins. Table 32: FC-SCA pin descriptions Pin Signal name Signal type 1* -EN bypass port A Low Voltage TTL output 2* 12 Volts 3* 12 Volts 4* 12 Volts 5* -Parallel ESI 6* Ground[1] 7* Active LED out Open collector out 8* Reserved 9* Start_1 [2] TTL input 10* Start_2 [2] TTL input 11* -EN bypass port B Low Voltage TTL output 12* SEL_6 TTL input/output 13* SEL_5 TTL input/output 14* SEL_4 TTL input 15* SEL_3 TTL input/output 16* Fault LED out Open collector out 17* DEV_CTRL_CODE_2 TTL input [2] 18* DEV_CTRL_CODE_1 TTL input [2] 19* 5 Volts 20* 5 Volts Pin Signal name 21 12 Volts charge Signal type 22 Ground 23 Ground 24* +Port A_in 25* -Port A_in 26 Ground 27* +Port B_in 28* -Port B_in 29 Ground 30* +Port A_out 31* -Port A_out Diff. PECL input pair Diff. PECL input pair Diff PECL output pair 32 Ground 33* +Port B_out 34* -Port B_out 35 Ground 36 SEL_2 37 SEL_1 Diff PECL output pair TTL input/output TTL input/output 38 SEL_0 TTL input/output 39 DEV_CTRL_CODE_0 [2] TTL input 40 5 Volts charge *Short pins in mating backpanel connector. [1] This pin may be connected to external logic to detect the presence of the drive. The drive connects this pin to the common ground. [2] Pins 9, 10, 17, 18, and 39 are option select pins and are tied high by the drive circuitry. The preferred electrical connection at the backplane is either open or grounded (open for the '1' setting, grounded for the '0' setting). Alternatively, these pins may be driven by a 3.3V logic device, pulled up to 3.3V through a pull-up resistor (recommended size of 10K ohm), or grounded through some other means. 70 Cheetah 10K.7 FC Product Manual, Rev. D

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106

70
Cheetah 10K.7 FC Product Manual, Rev. D
9.5.4
Pin descriptions
This section provides a pin-out of the FC-SCA and a description of the functions provided by the pins.
*Short pins in mating backpanel connector.
[1]
This pin may be connected to external logic to detect the presence of the drive. The drive connects this
pin to the common ground.
[2]
Pins 9, 10, 17, 18, and 39 are option select pins and are tied high by the drive circuitry. The preferred elec-
trical connection at the backplane is either open or grounded (open for the ‘1’ setting, grounded for the ‘0’
setting). Alternatively, these pins may be driven by a 3.3V logic device, pulled up to 3.3V through a pull-up
resistor (recommended size of 10K ohm), or grounded through some other means.
Table 32:
FC-SCA pin descriptions
Pin
Signal name
Signal type
Pin
Signal name
Signal type
1*
-EN bypass port A
Low Voltage
TTL output
21
12 Volts charge
2*
12 Volts
22
Ground
3*
12 Volts
23
Ground
4*
12 Volts
24*
+Port A_in
Diff. PECL input pair
5*
-Parallel ESI
25*
-Port A_in
6*
Ground
[1]
26
Ground
7*
Active LED out
Open collector out
27*
+Port B_in
Diff. PECL input pair
8*
Reserved
28*
-Port B_in
9*
Start_1 [2]
TTL input
29
Ground
10*
Start_2 [2]
TTL input
30*
+Port A_out
Diff PECL output pair
11*
-EN bypass port B
Low Voltage
TTL output
31*
-Port A_out
12*
SEL_6
TTL input/output
32
Ground
13*
SEL_5
TTL input/output
33*
+Port B_out
Diff PECL output pair
14*
SEL_4
TTL input
34*
-Port B_out
15*
SEL_3
TTL input/output
35
Ground
16*
Fault LED out
Open collector out
36
SEL_2
TTL input/output
17*
DEV_CTRL_CODE_2
[2]
TTL input
37
SEL_1
TTL input/output
18*
DEV_CTRL_CODE_1
[2]
TTL input
38
SEL_0
TTL input/output
19*
5 Volts
39
DEV_CTRL_CODE_0 [2]
TTL input
20*
5 Volts
40
5 Volts charge