Home » Seagate Manuals » Hard Drives » Seagate ST9146853SS » Manual Viewer

Seagate ST9146853SS Savvio 15K.1 SAS Product Manual - Page 68

Transmitter signal characteristics, Table 17

View all Seagate ST9146853SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Figure 18 defines the sinusoidal jitter mask. Peak-topeak sinusoidal jitter (in UI) 1.5 Sinusoidal jitter frequency (log/log plot) FNOM = 1.5 x 10 9 for 1.5 Gbps FNOM = 3.0 x 10 9 for 3.0 Gbps 1.0 0.1 0 FNOM / 25,000 FNOM / 1,667 Frequency (in kHz) Figure 18. Sinusoidal jitter mask 9.5.2.2 Transmitter signal characteristics Table 17 specifies the signal requirements at the transmitter end of a TxRx connection as measured into the zero-length test load. All specifications are based on differential measurements. The OOB sequence is performed at signal voltage levels corresponding to the lowest supported transfer rate. Table 17 specifies the signal characteristics. Table 17: Transmitter signal characteristics Signal characteristica Skewb Tx Off Voltagec Maximum rise/fall timed Minimum rise/fall timed Maximum transmitter output imbalancee OOB offset deltaf OOB common mode deltag Units ps mV(P-P) ps ps % mV mV 1.5 Gbps 20 < 50 273 67 10 ± 25 ± 50 3.0 Gbps 15 < 50 137 67 10 ± 25 ± 50 62 Savvio 15K SAS Product Manual, Rev. C

Section	Page
1.0 Scope	7
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.1.1 Electromagnetic susceptibility	9
2.1.2 Electromagnetic compliance	10
2.1.3 European Union Restriction of Hazardous Substances (RoHS)	11
2.2 Reference documents	11
3.0 General description	13
3.1 Standard features	14
3.2 Media description	14
3.3 Performance	14
3.4 Reliability	15
3.5 Formatted capacities	15
3.6 Programmable drive capacity	15
3.7 Factory-installed accessories	15
3.8 Options	16
4.0 Performance characteristics	17
4.1 Internal drive characteristics	17
4.2 Seek performance characteristics	17
4.2.1 Access time (Gen 2.0 LP data)	17
4.2.2 Format command execution time	18
4.2.3 General performance characteristics	18
4.3 Start/stop time	18
4.4 Prefetch/multi-segmented cache control	18
4.5 Cache operation	19
4.5.1 Caching write data	19
4.5.2 Prefetch operation	20
5.0 Reliability specifications	21
5.1 Error rates	21
5.1.1 Recoverable Errors	21
5.1.2 Unrecoverable Errors	21
5.1.3 Seek errors	22
5.1.4 Interface errors	22
5.2 Reliability and service	22
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	22
5.2.2 Preventive maintenance	22
5.2.3 Hot plugging the drive	22
5.2.4 S.M.A.R.T.	23
5.2.5 Thermal monitor	24
5.2.6 Drive Self Test (DST)	24
5.2.6.1 DST failure definition	25
5.2.6.2 Implementation	25
5.2.6.2.1 State of the drive prior to testing	25
5.2.6.2.2 Invoking DST	25
5.2.6.2.3 Short and extended tests	25
5.2.6.2.4 Log page entries	26
5.2.6.2.5 Abort	26
5.2.7 Product warranty	26
6.0 Physical/electrical specifications	29
6.1 AC power requirements	29
6.2 DC power requirements	29
6.2.1 Conducted noise immunity	31
6.2.2 Power sequencing	31
6.2.3 Current profiles	31
6.3 Power dissipation	33
6.4 Environmental limits	35
6.4.1 Temperature	35
6.4.2 Relative humidity	35
6.4.3 Effective altitude (sea level)	36
6.4.4 Shock and vibration	36
6.4.4.1 Shock	36
6.4.4.2 Vibration	38
6.4.5 Air cleanliness	38
6.4.6 Corrosive environment	38
6.4.7 Acoustics	39
6.4.8 Electromagnetic susceptibility	39
6.5 Mechanical specifications	40
7.0 Defect and error management	41
7.1 Drive internal defects/errors	41
7.2 Drive error recovery procedures	41
7.3 SAS system errors	42
7.4 Background Media Scan	43
7.5 Media Pre-Scan	43
7.6 Deferred Auto-Reallocation	43
7.7 Idle Read After Write	44
8.0 Installation	45
8.1 Drive orientation	45
8.2 Cooling	46
8.3 Drive mounting	47
8.4 Grounding	47
9.0 Interface requirements	49
9.1 SAS features	49
9.1.1 task management functions	49
9.1.2 Task management responses	49
9.2 Dual port support	50
9.3 SCSI commands supported	51
9.3.1 Inquiry data	55
9.3.2 Mode Sense data	55
9.4 Miscellaneous operating features and conditions	59
9.4.1 SAS physical interface	60
9.4.2 Physical characteristics	63
9.4.3 Connector requirements	63
9.4.4 Electrical description	63
9.4.5 Pin descriptions	63
9.4.6 SAS transmitters and receivers	64
9.4.7 Power	65
9.5 Signal characteristics	65
9.5.1 Ready LED Out	65
9.5.2 Differential signals	65
9.5.2.1 Eye masks	66
9.5.2.1.1 Eye masks overview	66
9.5.2.1.2 Receive eye mask	66
9.5.2.1.3 Jitter tolerance masks	67
9.5.2.2 Transmitter signal characteristics	68
9.5.2.3 Receiver signal characteristics	69
9.5.2.3.1 Jitter	70
9.5.2.3.2 Receiver jitter tolerance	70
9.5.2.3.3 Compliant jitter test pattern (CJTPAT)	70
9.5.2.3.4 Impedance specifications	71
9.5.2.4 Electrical TxRx connections	72
9.5.2.4.1 Transmitter characteristics	72
9.5.2.5 Receiver characteristics	75
10.0 Seagate Technology support services	77
Numerics	79
A	79
B	79
C	79
D	79
E	79
F	80
G	80
H	80
I	80
J	80
L	80
M	80
N	81
O	81
P	81
Q	81
R	81
S	81
T	82
U	82
V	82
W	82