Home » Seagate Manuals » Hard Drives » Seagate ST9250412AS » Manual Viewer

Seagate ST9250412AS Momentus 7200 FDE.2 SATA Product Manual - Page 39

Identify Device command

View all Seagate ST9250412AS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

4.2.5 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table below. All reserved bits or words should be set to zero. Parameters listed with an "x" are drive-specific or vary with the state of the drive. The following commands contain drive-specific features that may not be included in the Serial ATA specification. Word 0 1 2 3 4 5 6 7-9 10-19 20 21 22 23-26 27-46 Description Configuration information: • Bit 15: 0 = ATA; 1 = ATAPI • Bit 7: removable media • Bit 6: removable controller • Bit 0: reserved Number of logical cylinders ATA-reserved Number of logical heads Retired Retired Number of logical sectors per logical track: 63 Retired Serial number: (20 ASCII characters, 0000H = none) Retired Retired Obsolete Firmware revision (8 ASCII character string, padded with blanks to end of string) Drive model number: (40 ASCII characters, padded with blanks to end of string) Value 0C5AH 16,383 C837H 16 0000H 0000H 003FH 0000H ASCII 0000H 8000H 0004H x.xx ST9500421AS ST9500426ASG ST9500422AS ST9500421AS ST9320427ASG ST9320426ASG ST9320426AS ST9250464ASG ST9250414ASG ST9250412AS ST9250411AS ST9160419ASG ST9160418ASG ST9160413AS 47 (Bits 7-0) Maximum sectors per interrupt on Read multiple 8001H and Write multiple (16) 48 Reserved 4001H 49 Standard Standby timer, IORDY supported and may be dis- 2F00H abled Momentus 7200 FDE.2 SATA Product Manual, Rev. B 33

Section	Page
1.0 Introduction	7
1.1 System requirements	8
1.2 About Momentus 7200 FDE.2 SATA disc drives	8
1.2.1 Drive state upon shipment	9
2.0 Drive specifications	10
2.1 Specification summary table	10
2.2 Formatted capacity	12
2.2.1 LBA mode	12
2.3 Default logical geometry	12
2.4 Physical organization	12
2.5 Recording and interface technology	13
2.6 Physical characteristics	13
2.7 Seek time	14
2.8 Start/stop times	14
2.9 Power specifications	15
2.9.1 Power consumption	15
2.9.1.1 Typical current profile	16
2.9.2 Conducted noise	16
2.9.3 Voltage tolerance	16
2.9.4 Power-management modes	17
2.10 Environmental specifications	18
2.10.1 Ambient temperature	18
2.10.2 Temperature gradient	18
2.10.3 Humidity	18
2.10.3.1 Relative humidity	18
2.10.3.2 Wet bulb temperature	18
2.10.4 Altitude	18
2.10.5 Shock	19
2.10.5.1 Operating shock	19
2.10.5.2 Nonoperating shock	19
2.10.6 Vibration	19
2.10.6.1 Operating vibration	19
2.10.6.2 Nonoperating vibration	19
2.11 Acoustics	20
2.12 Electromagnetic immunity	20
2.13 Reliability	21
2.13.1 Free Fall Protection feature	22
2.14 Agency certification	22
2.14.1 Safety certification	22
2.14.2 Electromagnetic compatibility	22
2.14.3 FCC verification	23
2.15 Environmental protection	23
2.15.1 European Union Restriction of Hazardous Substances (RoHS)	23
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	24
2.16 Corrosive environment	24
3.0 Configuring and mounting the drive	25
3.1 Handling and static-discharge precautions	25
3.2 Configuring the drive	26
3.3 Serial ATA cables and connectors	26
3.4 Drive mounting	27
3.5 Drive integration	28
3.5.1 Drive installation	29
3.5.2 Consumer usage	29
3.6 Security Erase--ATA security commands	29
3.6.1 Secure Erase procedure	29
3.6.2 Drive State after Secure Erase	30
4.0 Serial ATA interface	31
4.1 Hot-Plug compatibility	31
4.2 Serial ATA device plug connector pin definitions	31
4.2.1 ATA Security policy exceptions	33
4.2.2 DriveTrust Mode support	34
4.2.3 Full Disc Encryption support	35
4.2.4 Supported ATA commands	36
4.2.5 Identify Device command	39
4.2.6 Set Features command	43
4.2.7 S.M.A.R.T. commands	44
5.0 Compatibility summary	45
5.1 Installation considerations	45
5.2 System Compatibility using WIndows XP SP2	45
5.2.1 BIOS versions tested in ATA Security mode	45
5.2.2 DriveTrust compatibility verification	48
5.3 Operating system versions tested	52
5.4 Compatibility test configurations	52
6.0 Seagate Technology support services	53
Index	55
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	56
K	56
L	56
M	56
N	56
O	56
P	56
Q	56
R	56
S	56
T	57
U	57
V	57