Sennheiser ew 300 IEM G2 Instructions for Use - Page 65

Using the components

Get Sennheiser ew 300 IEM G2 PDF manuals and user guides View all Sennheiser ew 300 IEM G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

³ · Connecting the headphones CAUTION! Danger of hearing damage! Listening at high volume levels for long periods can lead to permanent hearing defects. ̈ Set the volume for the connected headphones to the minimum before putting the headphones on. ̈ For monitoring purposes, connect the supplied earphones or any Sennheiser stereo headphones with 3.5 mm stereo jack plug to the headphone output (PHONES) ³. ̈ First, set the volume control · to the lowest volume by turning it to the left as far as possible. Then gradually turn up the volume. Using the components Switching the components on/off Switching the transmitter on/off ̈ Press the ON button ¶ to switch the transmitter on. ̈ To switch the transmitter off, press the ON button until "OFF" appears on the display. Note: The transmitter can only be switched off when the standard display is shown on the display panel. Within the operating menu, the ON button ¶ serves as the ESC (cancel) key, i.e. you cancel your entry and return to the standard display. After switch-off, the transmitter is in standby mode. To disconnect the transmitter from the mains, pull out the mains connector from the wall socket! Switching the receiver on/off Ƹ ̈ To switch the receiver on, turn the volume control Ƹ clockwise until it clicks. The red LED » lights up. ̈ To switch the receiver off, turn the volume control Ƹ counterclockwise until it clicks. The red LED » goes off. » Note: y The receiver has a short switch-on delay. y Remove the batteries or the accupack when the receiver will not be used for extended periods of time. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
18
Connecting the headphones
³
For monitoring purposes, connect the supplied earphones or any
Sennheiser stereo headphones with 3.5 mm stereo jack plug to the
headphone output (PHONES)
±
.
³
First, set the volume control
²
to the lowest volume by turning it to the
left as far as possible. Then gradually turn up the volume.
Using the components
Switching the components on/off
Switching the transmitter on/off
³
Press the
ON
button
·
to switch the transmitter on.
³
To switch the transmitter off, press the
ON
button until “OFF” appears on
the display.
Note:
The transmitter can only be switched off when the standard display is
shown on the display panel. Within the operating menu, the
ON
button
serves as the ESC (cancel) key, i.e. you cancel your entry and return to the
standard display.
After switch-off, the transmitter is in standby mode. To disconnect the
transmitter from the mains, pull out the mains connector from the wall
socket!
Switching the receiver on/off
³
To switch the receiver on, turn the volume control
Å
clockwise until it
clicks. The red LED
³
lights up.
³
To switch the receiver off, turn the volume control
Å
counterclockwise
until it clicks. The red LED
³
goes off.
Note:
y
The receiver has a short switch-on delay.
y
Remove the batteries or the accupack when the receiver will not be used
for extended periods of time.
CAUTION!
Danger of hearing damage!
Listening at high volume levels for long periods can lead to
permanent hearing defects.
³
Set the volume for the connected headphones to the
minimum before putting the headphones on.
±
²
·
³
Å