Sharp AR-157E AR-153E AR-157E Operation Manual Suite - Page 17

Using the RSPF/SPF, of originals.

Get Sharp AR-157E PDF manuals and user guides View all Sharp AR-157E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Using the RSPF/SPF The RSPF/SPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 8-1/2" x 14" and weighting from 14 lbs. to 23.9 lbs. • Before feeding originals in the original feeder tray, be sure to remove any staples or paper clips from them. • Before placing curled or wavy originals into the original feeder tray, be sure to flatten them. If not, original misfeeds may result. • The RSPF/SPF ( ) indicator on the operation panel will light up. If this indicator does not light up, the originals are not properly set or the RSPF/SPF is not properly closed. • Badly damaged originals may misfeed in the RSPF/SPF. It is recommended that such originals be copied from the original table. • Special originals such as transparency film should not be fed through the RSPF/SPF, but should be placed directly on the original table. 3 • Image loss (max. 5/32") can occur at the leading and trailing edges of the copies. Also image loss (max. 11/64" in total) can occur along the other edges of the copies. It can be 15/64" (max.) at the trailing edge of the second copy of two-sided copying. • To stop continuous copying using the RSPF/SPF, press the clear ( ) key. • Copying using one-sided to one-sided mode (AR-157E): Ensure that no indicator is lit among the original to copy indicators. 1 Make sure that no original is left on the original table. 2 Adjust the original guides to the size of originals. 3 Set the originals face up in the original feeder tray. Original face up Stream feeding mode The stream feeding mode allows easy operation of continuous copying from the RSPF/SPF. If the stream feeding mode has been enabled using user program No.4, the RSPF/SPF ( ) indicator will blink approximately 5 seconds after the last original has been fed by the RSPF/SPF. While this indicator is blinking, any new originals placed in the original feeder tray will be fed and copied automatically. If the stream feeding mode has been disabled, the start ( ) key must be pressed each time the originals are set even immediately after completion of a copy run from the RSPF/SPF. The default setting of the stream feeding mode is "ON". See "USER PROGRAMS" (p.23). 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
15
3
Using the RSPF/SPF
The RSPF/SPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2"
to 8-1/2" x 14" and weighting from 14 lbs. to 23.9 lbs.
1
Make sure that no original is left on the original table.
2
Adjust the original guides to the size
of originals.
3
Set the originals face up in the
original feeder tray.
Stream feeding mode
The stream feeding mode allows easy operation of continuous copying from the
RSPF/SPF. If the stream feeding mode has been enabled using user program No.4,
the RSPF/SPF (
) indicator will blink approximately 5 seconds after the last
original has been fed by the RSPF/SPF. While this indicator is blinking, any new
originals placed in the original feeder tray will be fed and copied automatically. If the
stream feeding mode has been disabled, the start (
) key must be pressed each
time the originals are set even immediately after completion of a copy run from the
RSPF/SPF. The default setting of the stream feeding mode is "ON". See "USER
PROGRAMS" (p.23).
•
Before feeding originals in the original feeder tray, be sure to remove
any staples or paper clips from them.
•
Before placing curled or wavy originals into the original feeder tray, be
sure to flatten them. If not, original misfeeds may result.
•
The RSPF/SPF (
) indicator on the operation panel will light up. If
this indicator does not light up, the originals are not properly set or the
RSPF/SPF is not properly closed.
•
Badly damaged originals may misfeed in the RSPF/SPF. It is
recommended that such originals be copied from the original table.
•
Special originals such as transparency film should not be fed through
the RSPF/SPF, but should be placed directly on the original table.
•
Image loss (max. 5/32") can occur at the leading and trailing edges of
the copies. Also image loss (max. 11/64" in total) can occur along the
other edges of the copies. It can be 15/64" (max.) at the trailing edge
of the second copy of two-sided copying.
•
To stop continuous copying using the RSPF/SPF, press the clear
(
)
key.
•
Copying using one-sided to one-sided mode (AR-157E):
Ensure that no indicator is lit among the original to copy indicators.
Original face up