Sharp AR-M208 AR-M208 Key Operator's Guide - Page 15

Timer Setting

Get Sharp AR-M208 PDF manuals and user guides View all Sharp AR-M208 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

KEY OPERATOR PROGRAMS TIMER SETTING The programs of this category are used to set the timers for some functions. These programs can be selected by using the and keys to highlight "TIMER SETTING", pressing the OK key, highlighting the desired program, and then pressing the OK key. Auto Power Off The auto power shut-off mode is a function to turn off the power to the fuser automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. This function will help lower the user's electricity bill, reduce waste of natural resources, and cut down on environmental pollution. The programmed time is set to 60 minutes for this function as shipped from the factory. The default time can be changed optionally within the prescribed range of time. We suggest you set the most appropriate time according to your usage pattern. The time until auto power shut-off occurs can be set to 10, 30, 60, 90, 120 or 240 minutes. When "AUTO POWER OFF" is selected and the OK key is pressed, the following display will appear. AUTO POWER OFF 60 min (10~240) 1. Select the desired time interval using the and keys. 2. Press the OK key. Auto Clear Use this program to set the time interval to return the copier to the initial settings after the last copy of a run has been completed. The time can be set to 0, 30, 60, 90, 120 or 240 seconds. The factory setting is 60 seconds. When "AUTO CLEAR" is selected and the OK key is pressed, the following display will appear. AUTO CLEAR 60 sec. (0~240) 1. Select the desired time interval using the and keys. G To disable the auto clear, select 0. 2. Press the OK key. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
KEY OPERATOR PROGRAMS
13
TIMER SETTING
The programs of this category are used to set the timers for some functions. These programs can be
selected by using the
and
keys to highlight "TIMER SETTING", pressing the OK key, highlighting
the desired program, and then pressing the OK key.
Auto Power Off
The auto power shut-off mode is a function to turn off the power to the fuser automatically once a
programmed length of time has elapsed without any copier operation after the last copy of a run is
made or power is turned on.
This function will help lower the user's electricity bill, reduce waste of natural resources, and cut down
on environmental pollution.
The programmed time is set to 60 minutes for this function as shipped from the factory. The default time
can be changed optionally within the prescribed range of time. We suggest you set the most
appropriate time according to your usage pattern.
The time until auto power shut-off occurs can be set to 10, 30, 60, 90, 120 or 240 minutes.
When "AUTO POWER OFF" is selected and the OK key is pressed, the following display will appear.
1.
Select the desired time interval using the
and
keys.
2.
Press the OK key.
Auto Clear
Use this program to set the time interval to return the copier to the initial settings after the last copy of a
run has been completed. The time can be set to 0, 30, 60, 90, 120 or 240 seconds. The factory setting
is 60 seconds.
When "AUTO CLEAR" is selected and the OK key is pressed, the following display will appear.
1.
Select the desired time interval using the
and
keys.
●
To disable the auto clear, select 0.
2.
Press the OK key.
AUTO POWER OFF
60
min
(10~240)
AUTO CLEAR
60
sec.
(0~240)