Sharp CD-MPX850 CD-MPX850 Operation Manual - Page 11

Preparation for Use - shelf system

Page 11 highlights

CD-MPX850 Preparation for Use Antenna connection Supplied FM antenna: Connect the FM antenna wire to the FM 75 OHMS jack and position the FM antenna wire in the direction where the strongest signal can be received. Supplied AM loop antenna: Connect the AM loop antenna to the AM and GND terminals. Position the AM loop antenna for optimum reception. Place the AM loop antenna on a shelf, etc., or attach it to a stand or a wall with screws (not supplied). FM antenna AM loop antenna Note: Placing the antenna on the unit or near the AC power cord may cause noise pickup. Place the antenna away from the unit for better reception. Installing the AM loop antenna: < Assembling > < Attaching to the wall > Wall Screws (not supplied) Speaker connection Connect the black wire to the FRONT SPEAKERS minus (-) terminal, and the red wire to the FRONT SPEAKERS plus (+) terminal. Speaker Light-Up connection 1. Connect the speaker light-up wires to the SPEAKERS LIGHT-UP jacks for speaker illumination. To turn off the speaker light-up feature, press the CLEAR/DIMMER button on the remote control for 2 seconds or more. LEFT SPEAKER RIGHT SPEAKER AC INPUT Note: Placing the right speaker light-up wire to the RIGHT jack and the left speaker light-up wire to the LEFT jack. Caution: Use speakers with an impedance of 6 ohms or more, as lower impedance speakers can damage the unit. Do not mistake the right and the left channels. The right speaker is the one on the right side when you face the unit. Do not let the bare speaker wires touch each other. Do not stand or sit on the speakers. You may be injured. Do not allow any objects to fall into or to be placed in the bass reflex duct. Incorrect Red AC INPUT Black 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

11
CD-MPX850
Preparation for Use
±
Antenna connection
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
±
Speaker connection
Connect the black wire to the FRONT SPEAKERS minus (-) terminal,
and the red wire to the FRONT SPEAKERS
plus (+) terminal.
±
Speaker Light-Up connection
1. Connect the speaker light-up wires to the SPEAKERS LIGHT-UP
jacks for speaker illumination. To turn off the speaker light-up
feature, press the CLEAR/DIMMER button on the remote control
for 2 seconds or more.
Note:
Placing the right speaker light-up wire to the RIGHT jack and the left
speaker light-up wire to the LEFT jack.
Caution:
Supplied FM antenna:
Connect the FM antenna wire to the
FM 75 OHMS jack and position the FM
antenna wire in the direction where the
strongest signal can be received.
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on
a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
< Assembling >
< Attaching to the wall >
Wall
Screws (not supplied)
AM loop
antenna
FM
antenna
Black
Red
z
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
z
Do not mistake the right and the left
channels. The right speaker is the one on the
right side when you face the unit.
z
Do not let the bare speaker wires touch
each other.
z
Do not stand or sit on the speakers. You may
be injured.
z
Do not allow any objects to fall into or to be
placed in the bass reflex duct.
Incorrect
LEFT SPEAKER
RIGHT SPEAKER