Sharp CD-MPX850 CD-MPX850 Operation Manual - Page 38

Troubleshooting chart

Page 38 highlights

CD-MPX850 Enhancing your system (continued) Troubleshooting chart Headphones Before plugging in or unplugging the headphones, reduce the volume. Be sure your headphones have a 1/8" (3.5 mm) diameter plug and impedance between 16 and 50 ohms. The recommended impedance is 32 ohms. Plugging in the headphones disconnects the speakers automatically. Adjust the volume using the VOLUME control. Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center. General Symptom The clock is not set to the correct time. When a button is pressed, the unit does not respond. No sound is heard. Possible cause Did a power failure occur? Reset the clock. (Refer to page 15.) Set the unit to the power standby mode and then turn it back on. If the unit still malfunctions, reset it. (Refer to page 40.) Is the volume level set to "0"? Are the headphones connected? Are the speaker wires disconnected? Advanced Features CD player Symptom Playback does not start. Playback stops in the middle or is not performed properly. Playback sounds are skipped, or stopped in the middle of a track. Possible cause Is the disc loaded upside down? Does the disc satisfy the standards? Is the disc distorted or scratched? Is the unit located near excessive vibrations? Is the disc very dirty? Has condensation formed inside the unit? 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

38
CD-MPX850
Advanced Features
Enhancing your system (continued)
±
Headphones
z
Before plugging in or unplugging the headphones, reduce the
volume.
z
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
z
Plugging
in
the
headphones
disconnects
the
speakers
automatically. Adjust the volume using the VOLUME control.
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
±
General
±
CD player
Symptom
Possible cause
z
The clock is not set to the
correct time.
z
Did a power failure occur? Reset
the clock. (Refer to page 15.)
z
When a button is pressed,
the unit does not respond.
z
Set the unit to the power stand-
by mode and then turn it back on.
z
If the unit still malfunctions, reset
it. (Refer to page 40.)
z
No sound is heard.
z
Is the volume level set to “0”?
z
Are the headphones connected?
z
Are the speaker wires discon-
nected?
Symptom
Possible cause
z
Playback does not start.
z
Is the disc loaded upside down?
z
Playback stops in the mid-
dle or is not performed
properly.
z
Does the disc satisfy the stan-
dards?
z
Is the disc distorted or
scratched?
z
Playback sounds are
skipped, or stopped in the
middle of a track.
z
Is the unit located near excessive
vibrations?
z
Is the disc very dirty?
z
Has condensation formed inside
the unit?