Sharp DT300 DT300 Operation Manual - Page 31

Image Projection

Get Sharp DT300 - DLP Projector - 700 ANSI Lumens PDF manuals and user guides
UPC - 074000364073
View all Sharp DT300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 31. 1 Plug the power cord into the wall outlet. • The POWER indicator illuminates red, and the projector enters standby mode. 2 Press on the remote control or on the projector. • The blinking green LAMP indicator shows that the lamp is warming up. Wait until the indicator stops blinking before operating the projector. • If the power is turned off and then immediately turned on again, it may take a short while before the lamp turns on. Note • After the projector is unpacked and turned on for the first time, a slight odor may be emitted from the exhaust ventilative holes. This odor will soon disappear with use. When the power is on, the LAMP indicator illuminates, indicating the status of the lamp. Green: Lamp is ready. Green blinking: Warming up. / Cooling down. Red: Change the lamp. LAMP indicator TEMP. LAMP POWER POWER indicator ON button INPUT button ON button INPUT buttons -30 %5@&@Q@Q Page 30 03.10.29, 2:41 PM "EPCF1BHF.BLFS+11$

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Image Projection
-30
TEMP.
LAMP
POWER
LAMP indicator
POWER indicator
ON button
INPUT button
ON button
INPUT buttons
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
31
.
1
Plug the power cord into the
wall outlet.
•
The POWER indicator illuminates red,
and the projector enters standby mode.
2
Press
on the remote control
or
on the projector.
•
The blinking green LAMP indicator
shows that the lamp is warming up.
Wait until the indicator stops blinking
before operating the projector.
•
If the power is turned off and then im-
mediately turned on again, it may take
a short while before the lamp turns on.
Note
•
After the projector is unpacked and
turned on for the first time, a slight
odor may be emitted from the exhaust
ventilative holes. This odor will soon
disappear with use.
When the power is on, the LAMP in-
dicator illuminates, indicating the sta-
tus of the lamp.
Green
: Lamp is ready.
Green blinking
:
Warming up. / Cooling
down.
Red
: Change the lamp.
DT-300_E_p29_43.p65
03.10.29, 2:41 PM
Page 30
Adobe PageMaker 6.5J/PPC