Sharp LC32DV24U Service Manual - Page 25

When Replacing Eeprom Memory Ic

Get Sharp LC32DV24U - 31.5inch LCD TV PDF manuals and user guides
UPC - 074000371293
View all Sharp LC32DV24U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding. 1. Turn on the POWER, and set to the ALL mode. 2. Set the VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (8) on the remote control for more than 2 seconds. 4. After the confirmation of each check sum, turn off the power. NOTE:The each item value might be different according to each set. Sub Micon check version Main Micon check version EEPROM check version Parameter CHECK SUM: 3D05 LCD PWR ON: 0000 SUB: DA0E783212 DTV: CA12E86111 EEPROM: W50X02PM00 Picture: _dispSmartPic Initial setting data check sum. POWER ON total hours. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) CONFIRMATION OF INITIAL DATA FIG. 1 If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA"). 1. Turn on the POWER, and set to the ALL mode. 2. Set the VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 2. NOTE: No need to set data other position than 7200~73FF. ADDRESS DATA INIT : 0001 008A SUB: DA0E783212 DTV: CA12E86111 EEPROM: W50X02PM00 FIG. 2 4. ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 5. Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink". 6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected. 7. Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary. 8. Repeat steps 4 to 6 until all data has been checked. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn on the Power. 10. Set the VOLUME to minimum. 11. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 12. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
1.
2.
3.
4.
Turn on the POWER, and set to the ALL mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button
(8)
on the remote control for more than 2 seconds.
After the confirmation of each check sum, turn off the power.
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION
Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are
displayed in 16 system of notation.
NOTE:
WHEN REPLACING EEPROM (MEMORY) IC
If you set a factory initialization, the total hours is reset to "0".
Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
NOTE:The each item value might be different according to each set.
1.
2.
3.
Turn on the POWER, and set to the ALL mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button
(6)
on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 2.
FIG. 1
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken
to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
CONFIRMATION OF INITIAL DATA
CHECK SUM:
3D05
LCD PWR ON:
0000
SUB:
DA0E783212
DTV:
CA12E86111
EEPROM:
W50X02PM00
Picture:
_dispSmartPic
Initial setting data check sum.
Sub Micon check version
Main Micon check version
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
EEPROM check version
Parameter
NOTE: No need to set data other position than 7200~73FF.
4.
5.
6.
7.
8.
9.
10.
11.
12.
The unit will now have the correct DATA for the new MEMORY IC.
ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn on the Power.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button
(1)
on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
FIG. 2
ADDRESS
DATA
INIT :
0001
008A
SUB:
DA0E783212
DTV:
CA12E86111
EEPROM:
W50X02PM00
C-3