Sharp NP-UM383WL Users Manual - Page 83

[OPTIONS(2)], AUTO POWER ON, operation by User Supportware, LAN feature, and Mail Alert feature.

Get Sharp NP-UM383WL PDF manuals and user guides View all Sharp NP-UM383WL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

[OPTIONS(2)] 5. Using On-Screen Menu Selecting Power-saving in [STANDBY MODE] The projector has two standby modes: [NORMAL] and [NETWORK STANDBY]. The NORMAL mode is the mode that allows you to put the projector in the power-saving condition which consumes less power than the NETWORK STANDBY mode. NORMAL When [NORMAL] is selected, only the following buttons and feature will work: POWER buttons on the projector cabinet and the remote control, AUTO POWER ON, and powering on from PC Control command. NETWORK STANDBY When [NETWORK STANDBY] is selected, the projector can be turned on over a wired LAN connection and only the following buttons, port, and features will work: POWER buttons on the projector cabinet and the remote control, powering on from PC Control command, AUTO POWER ON, operation by User Supportware, LAN feature, and Mail Alert feature. IMPORTANT: • When [NETWORK STANDBY] has been set for [STANDBY MODE] and the LAN has been in link-down condition for 3 minutes, [STANDBY MODE] will transit into [NORMAL] automticially for the purpose to save the consumption power. • When [NETWORK STANDBY] has been selected, [AUTO POWER OFF] becomes ineffective (displayed in grey) and [0:15] is selected auto- matically. • In the below conditions, setting of the [STANDBY MODE] is disabled and the projector will go into the SLEEP mode*. * Sleep mode refers the mode without functional restrictions by the [STANDBY MODE]. When [STANDBY MODE] → [NETWORK STANDBY] is selected - When [NETWORK SERVICE] → [AMX SETTINGS] → [ENABLE] is selected - When the signal is input to the computer, HDMI 1 IN or HDMI 2 IN terminals NOTE: • Even when [NORMAL] is selected for [STANDBY MODE], power on or off can be done by using the PC CONTROL port. • The power consumption in the standby mode will not be included in calculating CO2 emission reduction. • Your setting for [STANDBY MODE] will not be affected even when [RESET] is done from the menu. Enabling Direct Power On [DIRECT POWER ON] Turns the projector on automatically when the power cord is inserted into an active power outlet. This eliminates the need to always use the POWER button on the remote control or projector cabinet. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
7
3
5. Using On-Screen Menu
Selecting Power-saving in [STANDBY MODE]
The projector has two standby modes: [NORMAL] and [NETWORK STANDBY].
The NORMAL mode is the mode that allows you to put the projector in the power-saving condition which consumes
less power than the NETWORK STANDBY mode.
NORMAL
�������������������������������
When [NORMAL] is selected, only the following buttons and feature will work:
POWER buttons on the projector cabinet and the remote control, AUTO POWER ON, and powering on from
PC Control command
�
NETWORK STANDBY
��������������
When [NETWORK STANDBY] is selected, the projector can be turned on over a wired LAN connection and
only the following buttons, port, and features will work:
IMPORTANT:
• When [NETWORK STANDBY] has been set for [STANDBY MODE] and the LAN has been in link-down condition for 3 minutes, [STANDBY
MODE] will transit into [NORMAL] automticially for the purpose to save the consumption power.
• When [NETWORK STANDBY] has been selected, [AUTO POWER OFF] becomes ineffective (displayed in grey) and [0:15] is selected auto-
matically.
When [STANDBY MODE]
→
[NETWORK STANDBY] is selected
- When [NETWORK SERVICE]
→
[AMX SETTINGS]
→
[ENABLE] is selected
- When the signal is input to the computer, HDMI 1 IN or HDMI 2 IN terminals
NOTE:
• Even when [NORMAL] is selected for [STANDBY MODE], power on or off can be done by using the PC CONTROL port.
• The power consumption in the standby mode will not be included in calculating CO
2
emission reduction.
• Your setting for [STANDBY MODE] will not be affected even when [RESET] is done from the menu.
[OPTIONS(2)]
Enabling Direct Power On [DIRECT POWER ON]
Turns the projector on automatically when the power cord is inserted into an active power outlet. This eliminates the
need to always use the POWER button on the remote control or projector cabinet.
POWER buttons on the projector cabinet and the remote control, powering on from PC Control command,
AUTO POWER ON, operation by User Supportware, LAN feature, and Mail Alert feature.
•
In the below conditions, setting of the [STANDBY MODE] is disabled and the projector will go into the SLEEP mode*.
* Sleep mode refers the mode without functional restrictions by the [STANDBY MODE].