Sharp PG A20X Operation Manual - Page 30

Image Projection - reset

Get Sharp PG A20X - Notevision XGA LCD Projector PDF manuals and user guides
UPC - 074000364004
View all Sharp PG A20X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before carrying out the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 28. 1 Plug the power cord into the wall outlet. • The power indicator illuminates red, and the projector enters standby mode. 2 Press on the projector or on the remote control. • The power indicator illuminates green. After the lamp indicator illuminates, the projector is ready to start operation. ON button STANDBY button Power Lamp indicator indicator INPUT button Volume buttons Note •The lamp indicator illuminates, indicating the status of the lamp. Green: The lamp is ready. Blinking in green: The lamp is warming up or shutting down. Red: The lamp should be replaced. • If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take some time to illuminate. • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. • When "Anti-Theft" (see page 48) is set, the keycode input box will appear. Enter the keycode. Note • When entering the keycode, press the buttons previously set on the projector or the remote control. • For details about the Anti-Theft function, refer to "Anti-Theft (Setting the Anti-Theft)" on page 48. Volume buttons MKeycode input box ON button AV MUTE button INPUT buttons -26 PG-A20X_E_PDF_P26_31.p65 26 03.4.23, 9:57 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
-26
Image Projection
Basic Procedure
Connect the required external equipment to the pro-
jector before carrying out the following procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display to
another language, reset the language accord-
ing to the procedure on page
28
.
1
Plug the power cord into the wall
outlet.
•
The power indicator illuminates red, and
the projector enters standby mode.
2
Press
on the projector or
on the remote control.
•
The power indicator illuminates green.
After the lamp indicator illuminates, the
projector is ready to start operation.
Note
•
The lamp indicator illuminates,
indicating the status of the lamp.
Green:
The lamp is ready.
Blinking in green:
The lamp is warming
up or shutting down.
Red:
The lamp should be replaced.
•
If the projector is put into the standby
mode and immediately turned on
again, the lamp indicator may take
some time to illuminate.
•
When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds af-
ter the power has been turned on, and
then transmit the commands.
•
When
“
Anti-Theft
”
(see page
48
) is set,
the keycode input box will appear. Enter
the keycode.
Note
•
When entering the keycode, press the
buttons previously set on the projec-
tor or the remote control.
•
For details about the Anti-Theft func-
tion, refer to
“
Anti-Theft (Setting the
Anti-Theft)
”
on page
48
.
▼
Keycode input box
Volume
buttons
STANDBY
button
ON button
Power
indicator
Lamp
indicator
INPUT
button
INPUT buttons
Volume
buttons
ON button
AV MUTE button
PG-A20X_E_PDF_P26_31.p65
03.4.23, 9:57 AM
26