Sharp PG-C20XE Operation Manual - Page 20

Basic Operations, INPUT, Projector, Remote control, VOLUME, AV MUTE, ON/OFF, POWER - lampe

Get Sharp PG-C20XE - Notevision SXGA LCD Projector PDF manuals and user guides View all Sharp PG-C20XE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Operation Basic Operations 3 4 3 Slide the ZOOM knob. The image can be adjusted to the desired size within the zoom range. 4 Rotate the FOCUS ring until the image on the screen becomes clear. Projector ON/OFF POWER LAMP TEMP. KEYSTONE INPUT AUTO SYNC BACK ENTER MENU EXAMPLE 5 INPUT 1 (RGB) Mode d INPUT 3 (VIDEO) Mode 6 7 8 Remote control 8 7 5 6 INPUT 1 (COMPONENT) Mode g f INPUT2 (S-VIDEO) Mode s 5 Press INPUT to select the desired input mode. Press INPUT again to change the mode. • When the selected input signal is being received, "Adjusting The Image" will be displayed. • When no signal is being received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is being received, "NOT REG." will be displayed. 6 Press VOLUME on the remote control to adjust the volume. 7 Press AV MUTE on the remote control to temporarily turn off the picture and the sound. Press AV MUTE again to turn the picture and the sound back on. 8 Press ON/OFF on the projector or POWER on the remote control for over one second. Press ON/OFF or POWER again while the message is displayed. • If you accidentally pressed ON/OFF or POWER and do not want to turn off the power, wait until the power off screen disappears. • When ON/OFF or POWER is pressed twice, the POWER indicator will light up red and the cooling fan will run for about 90 seconds. The projector will then enter standby mode. • Wait until the cooling fan stops before disconnecting the power cord. • The power can be turned on again by pressing ON/OFF or POWER. When the power is turned on, the POWER indicator and the LAMP REPLACEMENT indicator light green. • The POWER indicator flashes if the right side filter cover is not securely installed. WARNING: The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the ON/ OFF button on the projector or the POWER button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Operation
17
Basic Operations
4
3
3
Slide the ZOOM knob. The image can be adjusted
to the desired size within the zoom range.
4
Rotate the FOCUS ring until the image on the
screen becomes clear.
5
Press
INPUT
to select the desired input mode.
Press
INPUT
again to change the mode.
6
7
Projector
Remote control
ON/OFF
POWER
LAMP
TEMP.
KEYSTONE
INPUT
BACK
ENTER
MENU
AUTO SYNC
8
7
5
6
8
•
When the selected input signal is being received,
“
Adjusting
The Image
”
will be displayed.
•
When no signal is being received,
“
NO SIGNAL
”
will be
displayed. When a signal that the projector is not preset to
receive is being received,
“
NOT REG.
”
will be displayed.
f
5
d
g
s
INPUT 1
(COMPONENT) Mode
INPUT 1
(RGB) Mode
EXAMPLE
INPUT 3
(VIDEO) Mode
INPUT2
(S-VIDEO) Mode
6
Press
VOLUME
on the remote control to adjust
the volume.
7
Press
AV MUTE
on the remote control to
temporarily turn off the picture and the sound.
Press
AV MUTE
again to turn the picture and the
sound back on.
8
Press
ON/OFF
on the projector or
POWER
on the
remote control for over one second.
Press
ON/OFF
or
POWER
again while the
message is displayed.
•
If you accidentally pressed
ON/OFF
or
POWER
and do not
want to turn off the power, wait until the power off screen
disappears.
•
When
ON/OFF
or
POWER
is pressed twice, the POWER
indicator will light up red and the cooling fan will run for
about 90 seconds. The projector will then enter standby
mode.
•
Wait until the cooling fan stops before disconnecting the
power cord.
•
The power can be turned on again by pressing
ON/OFF
or
POWER
. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light green.
•
The POWER indicator flashes if the right side filter cover is
not securely installed.
WARNING:
The cooling fan in this projector continues to run for about
90 seconds after the projector is turned off. During normal
operation, when turning the power off always use the
ON/
OFF
button on the projector or the
POWER
button on the
remote control. Ensure the cooling fan has stopped before
disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE
PROJECTOR OFF BY DISCONNECTING THE POWER
CORD. FAILURE TO OBSERVE THIS WILL RESULT IN
PREMATURE LAMP FAILURE.