Sharp XG-V10XU XG-V10XU Operation Manual - Page 5

Temperature Monitor Function, Lamp Monitor Function, Using the Carrying Handle - filter

Get Sharp XG-V10XU - Conference Series XGA LCD Projector PDF manuals and user guides View all Sharp XG-V10XU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Important Information IMPORTANT SAFEGUARDS Temperature Monitor Function If the projector starts to overheat due to setup problems or a dirty air filter, "TEMP." and " " will flash in the lower-left corner of the picture. If the temperature continues to rise, the lamp will turn off, the TEMPERATURE WARNING indicator on the projector will flash, and after a 90-second cooling-off period the power will shut off. Refer to "Lamp/Maintenance Indicators" on page 69, for details. • The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. Lamp Monitor Function When the projector is turned on after the lamp has been used for 900 hours, "LAMP" and " " will flash in the lower-left corner of the picture to advise you to replace the lamp. Check the "Lamp Timer" menu to confirm which lamp has been used for 900 hours and needs to be replaced. See pages 71 and 72 for lamp replacement. If the lamp has been used for 1,000 hours, the projector power will automatically turn off and the projector will enter standby mode. Refer to "Lamp/Maintenance Indicators" on page 69, for details. Carrying handle s Using the Carrying Handle When transporting the projector, carry it by the carrying handle on the side. CAUTION • Always put on the lens cap to prevent damage to the lens when transporting the projector. • Do not lift or carry the projector by the lens or the lens cap as this may damage the lens. • This equipment is very heavy, so to prevent injury take special care when carrying on your own. • Do not put down the equipment when the BNC-RCA adapters are connected. Using the Terminal Cover • When ceiling-mounting the projector, attach the terminal cover (supplied) to hide the connecting cables. • Use the terminal cover to hide the connecting cables when the projector is used on a desktop or high mounted. 1 Attach the terminal cover by aligning with the tabs on the projector. 2 Install the terminal cover using the two supplied user service screws attached. Optional lenses • Lenses are sold separately. • Be sure to have service personnel install optional lenses. E-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
E-4
Important
Information
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter,
“
TEMP.
”
and
“
”
will flash in the lower-left corner of the picture. If the temperature continues
to rise, the lamp will turn off, the TEMPERATURE WARNING indicator on the
projector will flash, and after a 90-second cooling-off period the power will shut
off. Refer to
“
Lamp/Maintenance Indicators
”
on page 69, for details.
•
The cooling fan regulates the internal temperature, and its performance is
automatically controlled. The sound of the fan may change during projector
operation due to changes in the fan speed.
Lamp Monitor Function
When the projector is turned on after the lamp has been used for 900 hours,
“
LAMP
”
and
“
”
will flash in the lower-left corner of the picture to advise you
to replace the lamp. Check the
“
Lamp Timer
”
menu to confirm which lamp
has been used for 900 hours and needs to be replaced. See pages 71 and
72 for lamp replacement. If the lamp has been used for 1,000 hours, the
projector power will automatically turn off and the projector will enter standby
mode. Refer to
“
Lamp/Maintenance Indicators
”
on page 69, for details.
IMPORTANT SAFEGUARDS
Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on
the side.
CAUTION
•
Always put on the lens cap to prevent damage to the lens when transporting
the projector.
•
Do not lift or carry the projector by the lens or the lens cap as this may
damage the lens.
•
This equipment is very heavy, so to prevent injury take special care when
carrying on your own.
•
Do not put down the equipment when the BNC-RCA adapters are
connected.
Using the Terminal Cover
•
When ceiling-mounting the projector, attach the terminal cover
(supplied) to hide the connecting cables.
•
Use the terminal cover to hide the connecting cables when the
projector is used on a desktop or high mounted.
1
Attach the terminal cover by aligning with the tabs on the projector.
2
Install the terminal cover using the two supplied user service
screws attached.
s
Carrying handle
Optional lenses
•
Lenses are sold separately.
•
Be sure to have service personnel install optional lenses.